Question about Yamaha 2004 Kodiak 450 Auto 4x4

1 Answer

Need torque specs for upper and lower ball joint and axle nut for 2004 yamaha kodiak 450

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 24 Answers

Http://www.imperialsupplies.com/pdf/A_FastenerTorqueCharts.pdf

Posted on Nov 01, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Yamaha 450 Kodiak battery not charging, new battery, volt meter not showing any voltage going to the battery


Hi Brian, get a digital volt meter and start the ATV measure the voltage at the battery or at the alternator it should read around 14 volts when charging, if it reads 12 volts the charging system is not working, check or a blown fuse or broken wire, if you can access the alternator directly measure at that point. It takes 14 volt output from the alternator to charge a 12 volt battery

May 06, 2017 | Yamaha 2005 Kodiak 450 Auto 4x4

1 Answer

Yamaha 450 Kodiak battery not charging


its either the voltage regulator (most likely) or the stator. you'll need a service manual to check the stator output.

May 06, 2017 | Yamaha 2005 Kodiak 450 Auto 4x4

1 Answer

Kodiak 450 idling to high to engage gear


turn the idle down? choke could be stuck too.

Jan 05, 2017 | Yamaha 2005 Kodiak 450 Auto 4x4

1 Answer

How to replace cv boots on atv


  1. First jack up vehicle.
  2. remove tire/rim
  3. remove cotter pin and castle nut from the end of the axle.
  4. disassemble spindle from upper/lower ball joints'
  5. separate spindle from axle by pulling spindle away from the vehicle.
  6. with two hands grasp axle and pull firmly to remove axle assembly from differential.
  7. remove torn cv boot, clean all old grease from cv joint.
  8. apply new grease and install new boot.
  9. secure clips on cv boot.
  10. Reassembly is reverse of disassembly.
  11. Consider purchasing the service manual for your make /model of atv from amazon. This manual will have step by step instructions and pictures for any repair or maintenance that you will need to perform.

May 15, 2016 | ATVs

1 Answer

What is the torque spec for rear axle/ hub nut


Going by this it would be 110 foot lbs...this was VERY hard to find...and I found it here...http://www.maultechatv.com/techguides/Service%20Manuals/YAMAHA/ATV-SxS%20Service%20Data%201995-2009.pdf

Hope this helps took me an hour to find this...

Jan 02, 2016 | Yamaha 2004 Bruin 350 Auto 4x4

1 Answer

Where is the fuse block on a yamaha Kodiak 450 2005


bet if you look under the seat you might find it .

Sep 27, 2015 | Yamaha 2005 Kodiak 450 Auto 4x4

Not finding what you are looking for?
Yamaha 2004 Kodiak 450 Auto 4x4 Logo

540 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha ATVs Experts

Kurt Bresler

Level 2 Expert

98 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

 Scott Tx
Scott Tx

Level 2 Expert

604 Answers

Are you a Yamaha ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...