Question about Polaris ATV

Open Question

I have a polaris magnum that the starter will not turn over, the battery is good. Everything powers up there is no safety switch on the brake the starter will not fire, what should i check next.

I have changed the solenoid, wiring harness, and handle bar, hi-lo starter part.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1201 Answers

SOURCE: wont start

There's only 2 more things that I can think of, check the fuse for the ignition, then the computor itself, you did everything else.It might be the problem and may not.

Posted on Jan 28, 2009

Ad
wd4ity
  • 4565 Answers

SOURCE: bike wont start replace start solenoid.when

You didn't mention what year model your bike is so I'll just generalize my response. Since you said that you replaced the solenoid, I'll assume that your bike is a 1988 model or earlier.

Your bike has a starter relay if it still has the stock wiring on it. Harley has used a starter relay since 1965 on the first model of ElectraGlide. Usually, it's underneath the battery tray or the seat or around that area.

On the back of your solenoid, you have three wire connections. Two very large connectors and one small connector. Make sure your bike is out of gear (in neutral) and use an old screwdriver to short between the large connector that comes from the battery and the small wire connection. The starter should engage and try to start the engine. If the ignition switch is on, it will start the engine. The starter will turn using this method with or without the switch being in the "on" position. If the starter works using this method, the problem is in either the relay or the neutral switch. If the starter does not turn the engine over, the problem is in the solenoid.

Now, let's check a few things. The small connector on the back of the solenoid should have a green or pink (depending on year) wire on it. Using a voltmeter or a test light, make sure you have voltage at the connector when you press the starter button with the switch in the "ON' position. If not, follow the wire to it's source, the relay.

The starter relay can be one of several different designs used throughout the years. It could be a small plastic cube, a small metal can, or a round phonelic relay. The relay should have four connections on it. A "hot" wire, a wire from the handlebar switch, the wire going to the starter, and a ground. The ground may be through the case itself. On the older Shovelhead bikes (1984 and earlier) there was a small short black wire that ran from the starter relay to the transmission for the ground. This wire must be intact or the relay would not work due to lack of a ground.

When you turn the switch on, one of the wires to the starter relay should become "hot". When you press the start button, you should hear a slight click and another of the smaller wires should now be "hot" as well, the one going to the starter.

On some year (1972 and later) models, the neutral switch was wired in with the starter relay. This was to prevent the bike from starting while "in gear" by disabling the relay. You'll have to figure this one out for yourself since I don't know what year model your bike is.

Now, you said you had power to the solenoid when you pushed the starter switch. So, let's assume that the starter failed the first test to told you aboue. If so, the problem is still most likely in the solenoid. Inside the solenoid, there is a large plunger with a copper disc on it. When you depress the starter switch, the coil in the solenoid becomes magnetized and pulls the plunger towards the back of the solenoid. This does two things, it engages the starter drive with the ring gear on the outer clutch drum and makes a high current electrical connection. The copper disc makes contact between the two large connections on the back of the solenoid from the inside. This connects the battery to the starter motor through the solenoid. If the black phonelic plate on the back of the solenoid is cracked or the contacts inside of it are badly burned, it will not work.

Now, if the solenoid is working correctly and you are getting voltage to your starter, it could be the brushes or something inside the starter. This is indicated if the starter trys to turn the engine over but just can't. It won't have enough power if the starter field windings are bad.

I hope I've given you something here that will help you solve your problem. This is basically the electrical part of the starter system. There are mechanical parts as well. If you hear the starter turning but the engine doesn't turn over, you have a mechanical problem. You can either repost or you can contact me directly at wd4ity@bellsouth.net I'll help if I can. Good Luck!

Posted on Nov 05, 2009

  • 2468 Answers

SOURCE: 96 ford explorer wont start. all power when turn key. nothing.

if it turns over from below,then its in the ignition switch and this also feeds power to the e.c.m. to make the engine fire so you either have a bad switch contact or the hot 12 volt wire to the ignition switch

Posted on Mar 20, 2010

  • 2 Answers

SOURCE: our polaris sportsman 500 6x6 won't start

Polaris seems to have a problem with this issue. I had the same problem with my bike and was able to fix it . I found a bad resetable fuse link located under the front cover. It looks like a plastic case with wires at both ends. cut the case and check the condition of that part. I found it was badly rusted . I removed the part and wired in a 10 amp fuse with a holder. wrapped it up to protect it and the problem was gone. lights worked fine as well as the cluster. Ed.

Posted on Aug 13, 2010

Sandpiper99
  • 71 Answers

SOURCE: Power windows on ford explorer

The main reason for this concern, especially if the door is used quite often and/or the vehicle has higher mileage is a break in the wiring going from the drivers door to the body. If you access this area by pulling the protective rubber back, shine a flashlight on these wires and look for a break (open circuit). look for shiny spots from the open copper wire. The stress from the door opening and closing is what causes the break and often you will find more than one broken wire. It will usually be a heavier gauge wire that doesn't flex as easily. Good luck, if you need more info, please ask.

Posted on Apr 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 polaris magnum 4X4, goes forward just fine but when you shift it into reverse it spits sputters backfires and won't move, any ideas????


you have a reverse safety like on riding mowers with deck engaged push and hold reverser button this link showes where and how it works --against bypassing a safety only video that showes the safety clearly 1995 Polaris Magnum 425 ATV Others Disable Reverse Override Function

Aug 10, 2018 | ATVs

1 Answer

Why will 2005 Polaris Magnum 330 fan not stop running when the ignition is turned off? The running fan drains the battery.


replace the faulty fan relay or check for a problem wire from the ignition to the sensor to the relay

Mar 03, 2016 | Polaris 2005 Magnum 330 4X2

1 Answer

Replaced battery and solenoid, not it wont start and smoke rolls out from under the tank/console area, what should I check?


The startr motor is fried or u hav worn cables w alot of resistenc. Fixit bfor car fire

Oct 23, 2015 | Polaris ATV

1 Answer

My polaris sportsman 570 will not start when I put the key and I have power to the lights on the dash but the engine will not turn over. I did turn it off in gear accidently.


If engine does not turn over you need to see if the starter is getting power and if it is any good. Also look for an inline safety switch for the starter that may be stuck in the open position and not allowing the electricity to enter the starter motor.

Sep 14, 2015 | ATVs

1 Answer

Why won't it start or even turn over?


check safety switch (emergency shut off)

Aug 11, 2015 | Polaris 2007 Sportsman 450

1 Answer

Where are the fuses on a 2001 Polaris 325 Magnum 4X4


Polaris 325 MAGNUM 4X4 HDS A00CD32FA Parts Manual

www.manualslib.com > ... > 325 MAGNUM 4X4 HDS A00CD32FA
View and Download Polaris 325 MAGNUM 4X4 HDS A00CD32FA parts manual online.Polaris Automobile Accessories Parts Manual. 325 MAGNUM 4X4 HDS ...

Aug 07, 2015 | Polaris ATV

1 Answer

2005 Polaris Ranger it was running fine and parked it about 2 weeks went by and it would not turn over put new battery in it thought it might be ignition switch put new one in and still won't start when...


I know nothing about this model but it sounds like some kind of safety lock is kicking in. like its not in neutral, brakes not on. whatever it needs to let it start.

Jul 17, 2017 | Polaris ATV

Not finding what you are looking for?
Polaris ATV Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Polaris ATVs Experts

unhappyed

Level 2 Expert

106 Answers

john h

Level 3 Expert

22408 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

Are you a Polaris ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...