20 Most Recent 2008 Dodge Ram Pickup 1500 Questions & Answers


Dodge ram 1500 5.7 hemi 2007 check. Engine light. Came on through a. Code. P0524 sayn oil pressure. To oil but oil light. Never. Came on runs. Good. U think. It's. The. Sensor

2008 Dodge Ram... | Answered on Nov 05, 2018


Willert9

You should not be giving out advice when you clearly have no idea what you are talking about. All dodge Chrysler Jeep products have automatic relearn on the TPMS system. Solid light means low tire pressure flashing light means one or more sensors are not working correctly or you just have installed new sensor on the vehicle and it needs to be relearned. On these make vehicles all you do is drive the vehicle up to 15 mins but usually will go out within 2 minutes

2008 Dodge Ram... | Answered on Aug 01, 2018


Just because it doesn't set DTC'S - diagnostic trouble codes , doesn't mean it can't have a problem with a OBD2 sensors , fuel system problem etc .... Taking the vehicle to a qualified technician that knows how to interpret sensor data an systems data should be done .
004 Fuel System Tests Start Here
003 Engine Peformance Tests Scan Data Tests

Could it be the transmission or fuel pump??? We test ,not guess ! Take it to a qualified repair shop.

2008 Dodge Ram... | Answered on Feb 24, 2018


IF you give the VIN number to the dealer and they look it up, it would have AHT or AHX option IF THE WIRING IS PRESENT.

2008 Dodge Ram... | Answered on Jan 17, 2018


ck for rust around bolts that mount the motor , I had a car that did this and turns out that rust made bad ground connections from a worn out bushing around shaft seal to wiper arm

2008 Dodge Ram... | Answered on Sep 15, 2016


It goes intake, exhaust from front to back as best I can tell. Look at the picture.
26281999-fa2g0hiogkliwezdqhsjwyqa-5-0.jpg

2008 Dodge Ram... | Answered on Sep 13, 2016


did you double check the fuel pump was connected properly and that the seal is intact?

2008 Dodge Ram... | Answered on Jul 09, 2016


cause it needs to build pressure in the tank before it can flow. when the tank is topped off theres too much fluid to build pressure then a little bit for the fluid to make its way to the fuel rail to make room for pressure to build

2008 Dodge Ram... | Answered on Jul 09, 2016


Answering the question is an electrical short. As for a repair it could be a bad dome switch, door jamb switch, or electrical short. The best I could from here is to tell you to remove the dome light fuse & that would solve your problem but that's not professional advice. That's a BAND AID. I could advise you to take it into a shop & have them tell you which one of these problems is your cause. Good Luck, Frank M

2008 Dodge Ram... | Answered on Feb 24, 2016


I think your vehicle takes a 15mm or 16mm socket. Normal spark plug wrench will not work. Visit your local Parts Store for more information. Have them show you a replacement plug for your truck and see what socket fits it.
Good Luck.

2008 Dodge Ram... | Answered on Feb 21, 2016


Hi John:
Those things can be (make that ARE) a pain.
I've found it essential to remove the shroud in order to replace the radiator.
Were you intending to run the engine without the shroud installed? That's not necessarily a good idea, both from a cooling and safety point of view.
Would it be possible for you to repair the shroud? It's quite rewarding to patch something up with pop rivets (use with washers) and save some inconvenience as well as $.
Once you figure out what holds the washer bottle in place you tend to remember. Skinned knuckles and broken parts are a great teacher.
Best of luck.
Cheers.

2008 Dodge Ram... | Answered on Feb 01, 2016


It may well be a failing fuel pump. The symptoms you describe are classic of a failing fuel pump.

However.. don't change parts in the hope of curing the problem. Let a workshop run a diagnostic test to identify the fault.

2008 Dodge Ram... | Answered on Jan 06, 2016


Could be crankshaft position sensor ! after a crank sensor is replaced it needs to have a relearn done , Dealer or some other independent repair shop . Take it an have it checked out , unless you have a factory scan tool or a professional type scan tool .

2008 Dodge Ram... | Answered on Jan 06, 2016


Hi Kenneth:
If you've got the right replacement belt, you should be able to install it using this technique.................
- The LAST pulley to fit will be the SPRING LOADED TENSIONER
- The grooved side of the belt is the INSIDE and it will go on the Outside of all grooved pulleys.
- The smooth side of the velt is the OUTSIDE and will go on the Inside of all smooth Pulleys.
- Just a bit of patient fun...... Thread the needle..... In/Out?In?Out
Last one... The tensioner...Use the flex bar... fit in the square hole... Pull..... slide belt over..... release tensioner. Ta Da!

2008 Dodge Ram... | Answered on May 29, 2015

Not finding what you are looking for?
2008 Dodge Ram Pickup 1500 Logo

252 questions posted

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ram Pickup 1500 Dodge

  • Ram Pickup 1500 Dodge

Most Popular Question

causes key fob keep killing batteries

  • Cars & Trucks
Loading...