2001 Dodge Ram 1500 Truck 2WD - Answered Questions & Fixed issues


You can get guide from many sites.. i know few
like reliable-store
error codes/ fault codes, wiring diagrams, schematic diagrams, torque specs, engine info, switches functioning, assemble, disassembly, complete refurbish, repair, installation every single thing is covered
within seconds u can get the access and it's totally illustrative complete

2001 Dodge Ram... | Answered on Feb 15, 2019 | 849 views


My personal suggestion
would be to go for these repair catalogs. I know this website www.reliable-store.com that i used to buy them from, and they sold online it was very good manual. Go ahead, I bet.

2001 Dodge Ram... | Answered on Mar 08, 2018 | 35 views


Just search google, OBD2 is an exact standard. There are diagrams there

2001 Dodge Ram... | Answered on Feb 26, 2018 | 197 views


At very cheap rates you can go for manuals from this store. Just check Secure Download DODGE RAM 1500 2500 3500 TRUCK SERVICE REPAIR MANUAL 1999...

2001 Dodge Ram... | Answered on Feb 15, 2018 | 844 views


Check codes or wires on FUEL INJECTORS after i purchased a jeep that ran same motor in my case the two wires going to fuel i jector was cracked and cuased ans issues but this with everything check when changing rotor you didnt demage and wires... Depending how its runing then shutting dowone can guess chrck wiring with TBS disconnect batt to rrset computer check all power lines to ecu if thry habe fuse link wires they may look fine but actual be disconnected.. Us proper tools to ensure power going to thr ecu.. Any fuel injection connection been disconnected in error... Meed more detail to give beyer answer.. Check code map sensor or crank sensor bit more than likely when doing tune up of the rotor something got disconnected or demaged take out spark plugs may be dirty grease oil on end of plug when installing can also cause this problem... Take your time CHECK FUEL LINE PRESEURE IF TOO LOW FUEL PUMP IS BAD... ALOT OF CHEEP tool sets on ebay to check fuel lone pressure air, fuel and spark everything else is sensors ecu engine management again possibly demaged, dirty or not gap new plug or demaged wire on ignition coil or distributor or fuel injector wires or tbs wires all meed checking and ecu power supply wires that often are FUSED LINK wires tested with gauge... Good luck i am sure you will find the issue.with patients.... Doesnt hurt to double check book in firing order year to l year can make a difference.. Even if same engine

2001 Dodge Ram... | Answered on Jan 13, 2018 | 84 views


Personally, Id suspect the voltage regulator. Depending on your vehicle, most of the alternators are self regulating. If its easy to pull, id pull the alternator and take it to Oreillys, Advance or Autozone and they will check it for free. If that checks good, then id look at a new computer.

2001 Dodge Ram... | Answered on Dec 27, 2017 | 58 views


CHECK YOUR WIRING MAY BE IS SHORTED OR CUT,SPECIALLY WHERE IS NEAR EXHAUST OR ANYWHERE TOUCHING ANYTHING,

2001 Dodge Ram... | Answered on Nov 26, 2017 | 146 views


Check that the blend door covering the heater core is opening completely. It's vacuum actuated and the vacuum is heavier when you accelerate.

2001 Dodge Ram... | Answered on Nov 12, 2017 | 248 views


You're going to have to shimmy up underneath and guide the dipstick tube back in and fasten at least one of the screws temporarily so you don't pull it out again. Its fairly easy and you shouldn't even need a jack due to the standing height of the 1500, I'm fairly broad around the chest and shoulders and i can get under my 94 which is the the same basic body stye quite easily with no jack to put back in my pesky neutral safety switch plug that occasionally likes to wiggle out

2001 Dodge Ram... | Answered on Nov 05, 2017 | 123 views


Yes there could be a build up of stuff in the fuel filter when you run the fuel level low. It could also be that the fuel gauge is not reading 100% correct either and you could be at a lower fuel level that it shows also.

2001 Dodge Ram... | Answered on Oct 15, 2017 | 106 views


Torque Converter Clutch Circuit/Open

2001 Dodge Ram... | Answered on Oct 13, 2017 | 161 views


That sounds like a bad heater core talking

2001 Dodge Ram... | Answered on Jul 13, 2017 | 163 views


Do a cleaning of fuel injectors before making that expense, then reset the ECM ,To see what happens

2001 Dodge Ram... | Answered on Jul 13, 2017 | 143 views


Could be u-joints. My wife's Pathfinder developed a vibration at highway speeds. A little research revealed the front driveshaft u-joints bearings would begin to fail causing some play. Took it in to have them inspected and sure enough- the little needle bearings were grinding down to dust. Replaced with greesable units and vibration is gone.
Certainly worth checking out.

2001 Dodge Ram... | Answered on May 19, 2017 | 226 views


It sounds to like a bad ground some where. Clean your ground were it is grounded to the engine. If that does not work change the ground wire.

2001 Dodge Ram... | Answered on Apr 15, 2017 | 63 views


The spindle is what holds the front tires on. The axle is what holds the rear tires on. To remove the spindle, you have to remove the brake caliper first the remove the ball joint nuts. hit the spindle were the ball joints go in. The shock will release the ball joints. To remove the axles, you have to remove the differential plate, spin the differential until you see the bolt that locks the center pin in. remove both. push in the axle and remove the C clip. pull the axle out.

2001 Dodge Ram... | Answered on Oct 15, 2016 | 160 views

Not finding what you are looking for?
Cars & Trucks Logo

1,567 questions posted

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...