2003 Jeep Grand Cherokee - Answered Questions & Fixed issues

What kind of Jeep (model,engine size).
Is it turning over?
Is the battery dead?
I need alot more information.

2003 Jeep Grand... | Answered on Jul 14, 2019 | 226 views

Look into the turn signal switch itself. Have the wiring checked.

2003 Jeep Grand... | Answered on Jun 26, 2019 | 28 views

Read this post about a lot of electrical problems. It will give you an idea on what to look for.
When it does not crank, check to see if voltage is getting to the starter. If it is, hit the starter. If it starts , replace it.

2003 Jeep Grand... | Answered on May 02, 2019 | 27 views

When you say the jeep will not turn over, you mean that it will not crank? If that is so then you may have a bad starter or coolant may have filled a cylinder with water. Pull out the spark plugs and see if it will crank over, check to see if water comes out of the heads when cranking. If it still does not turn over, check the starter.

2003 Jeep Grand... | Answered on Apr 22, 2019 | 60 views

Some fixya user told me a website reliable-store it is very good.. I used it to repair my shredder it had some spark issue which wasn't easily fixed. you can go there and try

2003 Jeep Grand... | Answered on Mar 02, 2019 | 476 views

Unfortunately, the relay may be located inside the transmission. Try utube if you have not already.

If you need further help, reach me via phone at https://www.6ya.com/expert/gary_9c859f4aa7e5ab10

2003 Jeep Grand... | Answered on Feb 21, 2018 | 262 views

Have them check your fuel filter, may be time to change- please also google the jeep to see if this is common!? Good Luck Stevo!!

2003 Jeep Grand... | Answered on Jan 14, 2018 | 30 views

code p 0122 causes are wiring short to ground , TP/APP sensor --ECM
or also wiring open/ short to ground / short to positive TP/APP---ECm
so check the wiring and connections
code p 0107 is map and /or BARO sensor --low input===causes ---wiring short to ground ---MAP sensor ---BARO sensor--ECM

2003 Jeep Grand... | Answered on Dec 23, 2017 | 50 views

remove door panel and check to see if glass is attached to bar that raises the window up and down as they do come loose
I would use a good glue check with the window repair for some
so you get the right stuff

2003 Jeep Grand... | Answered on Dec 02, 2017 | 77 views

Steering pump belt loose or worn.

2003 Jeep Grand... | Answered on Sep 20, 2017 | 105 views

Yes they are.

2003 Jeep Grand... | Answered on Aug 29, 2017 | 159 views

run the fault codes
servo/ solenoid. or sensor problems

2003 Jeep Grand... | Answered on Aug 21, 2017 | 58 views

You don't need to go by auto zone to have codes check ! Chrysler , Dodge and jeep vehicle's can be checked without a scanner ! Turn the key on then off then back on then off again an then on an leave it on . Check in the odometer an it will show P codes ,then it will show done !
What size engine does it have ? 4.0 or 4.7 L
Fuse #17 10 amp located in the junction block powers pin #16 at the DLC . This would power up a scan tool . Not a PCM fuse !
Your vehicle does not have a separate control module for the transmission ,it is part of the PCM - powertrain control module !
Jeep vehicles with stalling an idle going high then low ( surging ) is caused most of the time by a bad TPS - throttle position sensor ! An don't use one from the aftermarket , use factory parts !

2003 Jeep Grand... | Answered on Jun 02, 2017 | 130 views

If you think that faulty brakes are OK then fine, keep driving it without looking to find the issue.
If you have ABS, suspect the ABS controller under the brake pump.

2003 Jeep Grand... | Answered on May 28, 2017 | 61 views

code p 0340 refers to cam shaft position sensor(CMP) sensor A bank 1--circuit malfunction====causes --wiring-- CMP sensor-- ECM
code p 0700 refers to transmission control system/ MIL--malfunction===causes --wiring---TCM
parts are available on line from e-bay , wreckers , junk yards manufacturer spares departments and would be delivered within 30 days so why are you waiting 7 months to get parts

2003 Jeep Grand... | Answered on May 07, 2017 | 88 views

go to your desired station ex 99.9 and hold down 1 on the preset line til it beeps.

2003 Jeep Grand... | Answered on Mar 24, 2017 | 291 views

Not finding what you are looking for?
2003 Jeep Grand Cherokee Logo

1,565 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Jeep Experts


Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides