20 Most Recent 1999 Jeep Grand Cherokee Questions & Answers

I don't think you need a wiring diagram.
Jeep had alot of problems with the lock accuator in the tailgate.

1999 Jeep Grand... | Answered on Jun 28, 2019

sounds like burnt out bulb. This is usually an indication when the bulb blows. Turn on blinker and check front and back to see which bulb is out..

1999 Jeep Grand... | Answered on May 31, 2019

Jeep has always had a problem down the line with the shifter linkage usuallly under the shifter, you have to take apart the console or column and locate whats broken inside there. I've had this issue myself with Cherokees too .

1999 Jeep Grand... | Answered on May 31, 2019

Could be a dirty intake manifold and IAC valve. Spray some intake cleaner into the throttle body with the engine running to clean the system.

1999 Jeep Grand... | Answered on May 02, 2019

Watch this video. It is on a 2000 but may be close to the same as a 1999.


1999 Jeep Grand... | Answered on Mar 21, 2019

In the fuel evap system you may have a defective leak detection pump.

1999 Jeep Grand... | Answered on Mar 21, 2019

I take help from online websites that have this service like helping in repair some like reliable-store have instant help.. others are a bit slow which I don't prefer... rest is up to u.. U can also get free manuals

1999 Jeep Grand... | Answered on Mar 14, 2019

Oil gauge may be bad, you said you changed the oil sending unit, and tried a aftermarket which worked, so the other option is to have you oil gauge checked. The sending unit may be good but you gauge is not reading proper.

1999 Jeep Grand... | Answered on Jan 22, 2019

If the alarm goes off, it its because it was armed in the first place. You mist disarm it before entering the vehicle. To disarm it push the remote control unlock button or open eithe front door or liftgate using the key in the keylock.

1999 Jeep Grand... | Answered on Jan 18, 2019

crank sensor would be first guess. second would be bad pcm. try this. start it and whiles its idling wiggle the 3 connectors at the pcm..does it die? theres your problem. if not replace the crank sensor

1999 Jeep Grand... | Answered on Jan 14, 2019


If fuel pressure is low and you have already replaced the fuel pump, then the problem is usually the fuel pressure regulator. The pressure regulator is in same assembly with fuel filter. The assembly is located to the fuel tank, bolted to the truck's frame. The pressure is tested connecting a gauge like this : Set Sealey VSE952 to the port on the fuel rail. The pressure on Grand Cherokee must be around 49 psi plus or minus 5 psi. If engine runs but pressure is below 44.2 psi , check for a blockage in fuel supply line between fuel rail and fuel pump module (e.g.kinked line). If the line is not blocked, replace fuel pressure regulator and filter. Test pressure with and without fuel cap on.

Another test to be done is reading pressure, then shutting the engine off with the gauge connected. If pressure goes down too quick, then the regulator is defective. After 5 minutes the pressure should not go below 24 psi. If it does replace the regulator.

If regulator is OK check for leaks at the injectors that can cause fuel pressure drops.To check for injectors leakage clamp off the rubber hose of the pressure gauge tool between fuel rail and the port. If pressure staysr above 24 psi and before was dropping, then a fuel injector or the fuel rail is leaking.

Below a diagram representing the fuel rail and test port. The engines from same years like your six cylinder have the port and rail in the same position.




1999 Jeep Grand... | Answered on Sep 30, 2018

is it all wheel drive? It's probably your front drive shaft. Very common.

1999 Jeep Grand... | Answered on May 16, 2018

Pretty simple unbolt and bolt back on operation. One thing though is most rebuilt pumps come with no pulley and you will need a machine shop to transfer yours to the new one. A special tool is necessary to do that so don't attempt it without the tool. If you haven't ever done this work, get a manual such as haynes or chiltons...it will not only help you there but in the future too.
After it's installed, fill the reservoir with power steering fluid and gently turn the steering wheel all the way in one direction (running) and then all the way in the other direction. Re-fill the reservoir and do the same again 'till the air in the system has been purged. Some fluid foaming and slight noise is normal but should disappear after a half hour or so.

1999 Jeep Grand... | Answered on Apr 18, 2018

youll have to run switched 12 volts to them yourself

1999 Jeep Grand... | Answered on Feb 21, 2018

reverse switch is located on the transmission usually it has two wires,bridge the wires together if reverse lights come on you have a faulty switch

1999 Jeep Grand... | Answered on Jan 12, 2018

when its idling try wiggling the three connectors at the pcm. if it dies you need a pcm because there are broken solder joints inside. junkyard units may work but are suspect for the same issue. been there done that with my 98. 99 was fine except for breaking piston skirts in two engines!!

1999 Jeep Grand... | Answered on Dec 25, 2017

indicates wind turbulence noise
possible around rear view mirrors , weather shields , door edge , bonnet edge , headlights
trial and error is to place tape over adjoining edges to see where a placed tape stops the noise

1999 Jeep Grand... | Answered on Nov 27, 2017

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

3,832 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Jeep Experts


Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Grand Cherokee Jeep

  • Grand Cherokee Jeep

Most Popular Question

1999 8 cyl 4 7 jeep grand cherokee

  • Cars & Trucks