Question about 2003 Hyundai Elantra
I need to replace the purge valve in my 2003 Hyundai Elantra. I have the new purge valve and am ready to install it. However, I have no idea where the old one is located. I only know that it's under the good somewhere. If anyone knows where the purge valve is located, please help. Thank you.
I sent to an auto parts place and bought it and casually asked the clerk where it went. He almost offered to go out into the parking lot to help me. He told me where it went, but then I forgot. They ran out of manuals (handy and cheap), but I got one on order. PS: Kia used the same one and it costs either the same or less. Back then there really wasn't much difference between Kias and Hyundais. You could call up one of the nationally known auto parts suppliers and simply ask the guy over the phone and tell him you'll come down and pick it up if he has one.
Posted on Mar 18, 2013
You could sell the parts for less money$$$$$.
Posted on Feb 24, 2014
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
There is a purge solenoid for the EVAP system and it is item no.# 1 shown in the diagram below. You have to follow the purge valve vacumn hose to find the charcoal cannister if you need to inspect.
I have included a description of the EVAP system for your understanding.
EVAPORATIVE EMISSION (EVAP) CONTROL SYSTEM
The EVAP and on-board refueling vapor recovery (ORVR) system consists of a fill vent valve, fuel shut-off valve, fuel cut (roll-over) valve, fuel liquid/vapor separator, EVAP canister, EVAP canister purge solenoid valve, EVAP canister close valve, vacuum relief filler cap, and connecting lines and hoses. ORVR system is designed to prevent the release of fuel vapors during refueling. During refueling, as fuel enters the fuel tank, a vacuum is created in filler pipe, drawing air into the filler pipe and tank. Fuel vapor in fuel tank is then forced to the EVAP canister via the fill vent valve and the fuel liquid/vapor separator. A fuel tank pressure sensor is used for detecting EVAP system leaks by comparing pressures inside and outside of fuel tank.
EVAP Canister Purge Solenoid Valve
Fuel vapors are vented into the EVAP canister during refueling and when ignition is off. When engine is at normal operating temperature and engine speed is greater than idle, a thermovalve opens and allows vacuum to open the purge control valve. Canister vapors are then drawn into the intake manifold for burning during combustion. The purge control valve is kept closed during idle and engine warm-up to reduce HC and CO emissions.
Posted on Dec 16, 2010
You will need to remove the right front wheel & wheel well liner. The canister purge valve is behind the cover. It should have two tube going into the bottom and one on the side near the top.
You can fix it!
If this helps you out please rate me!
Posted on Mar 19, 2009
There were two different engines which were installed in the 2003 Tiberon... the 2.0 liter 4 cylinder:
And the 2.7 Liter V6:
Posted on Jun 06, 2009
Tips for a great answer:
Apr 13, 2016 | Hyundai Cars & Trucks
Apr 09, 2016 | Hyundai Cars & Trucks
Jul 06, 2015 | Hyundai Cars & Trucks
Mar 16, 2017 | Hyundai Motor 2003 Elantra
Oct 16, 2009 | Hyundai Motor 2003 Elantra
Oct 13, 2009 | Hyundai Motor 2003 Elantra
Jun 06, 2009 | 2003 Hyundai Tiburon
May 03, 2009 | Hyundai Elantra Cars & Trucks
24,962 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: