Question about 2000 Jeep Grand Cherokee
Ecu internal malfunction code 11
Posted by Anonymous on
It probably has a broken solder joint inside. its very common on a lot of jeeps of that vintage. there are a few you tube vids describing and fixing the problem
Posted on Nov 19, 2018
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
CEL Code P1762 is Governor Pressure Sensor Offset Improper Voltage. Make sure all your wires going to the sensor are ok, then if they are I would look into a new Sensor. Hope this gives you some direction. Thanks for Using FixYa!
Posted on Nov 30, 2008
oil pressure problem should be checked independently of other problems...Use a good accurate mechanical gauge to check. If pressure is good (no less than 15psi at idle hot (I prefer to see at least 20) check dash grounding, block ground and if OK, change sending unit. Dash and body ground can influence operation of shift and body control modules so indirectly your problem may or may not be related, depending upon what you find while testing. And it could turn out to be a defective module! They are expensive and just plugging new ones in may work, but then again, it might not. I might be totally incorrect on this...that's the value of actually being there instead of doing this by "remote control".
If you read the numerous posts pertaining to all vehicles, you will see that you are not alone with electrical problems...As long as the engineers who design this stuff, keep using "modules" to replace ordinary simple and reliable systems, we will continue to have these problems. Do some testing and I'm sure you will find a solution! (I'm still waiting for someone to make a program for a PC that will give a complete readout of every system in a vehicle, including exact faults instead of general system "suggestions")
Posted on Apr 07, 2009
Trouble Code: P0113 (4.0L L6 VIN S Auto)
IAT Sensor Circuit High Input Print this code data Number of Trips to Set Code: 1
OBD II Monitor Type: CCM Details
Indicators: MIL Details
Check with ignition on or engine running; battery voltage more than 10v; The PCM detected the IAT Sensor input was over 4.90v (exc. Dakota, Durango, Ram) or 4.98v (Dakota, Durango, Ram) for 3 seconds.
Posted on Dec 01, 2009
These conditions MUST be ruled out entirely.
Check for any of the following conditions/mechanical problems.
AIR INDUCTION SYSTEM - must be free from leaks
ENGINE VACUUM - must be at least 13 inches in neutral
ENGINE VALVE TIMING - must be within specifications
ENGINE COMPRESSION - must be within specifications
ENGINE EXHAUST SYSTEM - must be free of any restrictions or leaks
ENGINE PCV SYSTEM - must flow freely
TORQUE CONVERTER STALL SPEED - must be within specifications
POWER BRAKE BOOSTER - no internal vacuum leaks
FUEL - must be free of contamination
FUEL INJECTOR - plugged or restricted injector; control wire not connected to correct injector.
Unfortunatly, a scan tool will be required to monitor o2 sensor voltages while the engine is running in closed loop. This code you are displaying is NOT an easy solution to trace down. I expect you had an exhaust leak and is why the cats were replaced? Anyway, if so, the PCM can reset the light after a few GOOD trip readings occur that will satisfy the PCM's no fault signal, otherwise the JEEP dealer is going to be your only solution and a pressure test should be performed.
Posted on Mar 31, 2010
P0301 is #1 cylinder misfire detected and is most likely related to a worn spark plug that is need of replacement. All plugs should be replaced if replacing one. Not sure how many miles you have on this vehicle, or if plugs were ever installed, but this is the basic step to take in diagnosis.
Posted on Jun 02, 2010
Tips for a great answer:
Feb 06, 2013 | Jeep Cherokee Cars & Trucks
Trouble Code: P0846
A/T 2/4 Pressure Switch Circuit Malfunction
2/4 pressure is incorrect, or internal transmission faults exist 2/4 pressure switch circuit is open, shorted to ground or power 2/4 pressure switch is damaged or it has failed TCM relay power circuit to L/R switch is open (loss of B+) PCM/TCM has failed
May 16, 2012 | 2000 Jeep Grand Cherokee
Mar 07, 2012 | 2002 Jeep Grand Cherokee
Apr 14, 2011 | 1996 Jeep Grand Cherokee
Mar 15, 2011 | 1995 Jeep Grand Cherokee
Feb 11, 2011 | 1994 Jeep Grand Cherokee
Sep 07, 2010 | 2000 Jeep Grand Cherokee
Jan 05, 2009 | 1994 Jeep Grand Cherokee
184 people viewed this question
Usually answered in minutes!