Question about Cars & Trucks

1 Answer

2000 mitsubishi galant 4 cyl, 4 door. Rear right door had seat belt slammed in the door. Closed it properly and now when trying to open door from inside latch it won't pull the lever to unlock and open it. manual locking mechanism won't engage or disengage. Won't open from out side handle. Suggestions? Perhaps a good link to a diy fix?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 408 Answers

Pull the door panel off and inspect the door latch. Sounds like you jammed or bent part of it out of place. If the handles are very loose, check and see it the door latch arm popped out of place

Posted on Nov 10, 2013

Ad

4 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
warlock61

warlock61

  • 659 Answers

SOURCE: Driver side door lock seems mechanically "stuck"

there are several screws you have to remove remove the trim piece around the inside handle the panel lifts off dont pry it off or it will break the door latch usually binds and has to be replaced

Posted on Mar 09, 2009

clint

  • 119 Answers

SOURCE: Passat rear drivers side door won't open

On a similar problem i removed the window controll switch unit on the drivers door and cleaned the multipin socket and this solved the same and other problems i had.

Posted on Jan 28, 2010

Aivo Pütsep

  • 4 Answers

SOURCE: Driver's door won't open inside

Hey, You need to remove the panel otherwise u can't reattach the metal sticks that move the locks, but i think it's hard to remove it in a closed posision when u don't brake it

Posted on May 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car wont start after tuneup on a 2000 4 cyl. mitsubishi galant


go over your work,Maybe you bumped a wire while working on it.

Feb 17, 2013 | 2000 Mitsubishi Galant

1 Answer

Where is the camshaft sensor located 2000 Mitsubishi Galant


Probably behind the camshaft sproket. Do you see any wireing going into the timeing cover? how hard is it to remove the top timeing cover & have a look should only be a few bolts

Jun 28, 2012 | Mitsubishi Galant Cars & Trucks

2 Answers

2005 chrysler town & country fuse box location


There are 2 fuse blocks. one is
when you open your drivers door look at the dash board on the side, right where the door and the dash come to gather when you close your door, that panel just pulls off, and there they are.
The other is the fuse box is in the eng compartment left side black box
by the fender

Jan 02, 2012 | Ford Tobago Cars & Trucks

1 Answer

How do i change the power steering pump belt on my 2003 mitsubishi galnt 4 cyl . ?


on the left side of motor is the power steering pump to the right is a bolt head (14mm) turn it counterclockwise until the belt is loose enough to remove. reverse proceedure to replace

Dec 18, 2010 | 2003 Mitsubishi Galant

1 Answer

How do you change a fuel pump for a 2000 Mitsubishi Galant


PROPERLY RELIEVE THE FUEL SYSTEM PRESSURE.TURN OFF RADIO.DISCONNECT NEGATIVE BATTERY CABLE.REMOVE REAR SEAT CUSHION BY PULLING THE SEAT STOPPER OUTWARD AND LIFTING THE LOWER CUSHION UPWARD.REMOVE ACCESS COVER.REMOVE FUEL PUMP WIRING.REMOVE THE RETURN HOSE AND THE HIGH PRESSURE FUEL HOSE.REMOVE FUEL PUMP MOUNTING NUTS AND REMOVE THE PUMP ASSEMBLY.INSTALL FUEL PUMP ASSEMBLY TO FUEL TANK.TORQUE PUMP RETAINING BOLTS 22 INCH POUNDS.

Oct 26, 2010 | 2000 Mitsubishi Galant

1 Answer

2000 Mitsubishi Galant 4 cyl ES underhood squeal on right side


The probable causes are: 1. The drive belts are slipping. 2. The drive pulleys for some engine accessories are misaligned. 3. You have turned the steering wheel to the limits. 4. The drive belts are loose.5. Your brake drum backing plates are rubbing against the brake drum. The brakes also might be a problem. check the brake drums/discs. Finally check your wheel and wheel alignment.

May 08, 2010 | 2000 Mitsubishi Galant

1 Answer

2000 Mitsubishi Galant 4 cyl ES underhood squeal on right side


Be gentle with my rating. I am a long ways away. It sounds like a fan belt. You should pop the hood next time and see how it sounds when you have the squeeling going on. Fan belts will squeel until the get warmed up and then stop because the heat makes them grab the way they are ment too. Let me know, Raz

Apr 19, 2010 | 2000 Mitsubishi Galant

1 Answer

'01 galant 4 cyl timing belt failure


plastic cover dont mean nothing put timing back in then install belt

Mar 22, 2009 | 2001 Mitsubishi Galant

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...