Question about 1990 Ford Thunderbird

1 Answer

How do you change u-joints

Do you have to drop the rear end?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 53,746 Answers

No . it is not normal to have to this as the Cross is bolted to the pinion flange with 2 small bolts for each side. The drive shaft will slide out of the rear of the gear box normally or if there is a flange there unbolt the 2 halves of the flange and remove it . Some diff pinions have the same arrangement depending on the make and capacity of the diff and torque requirements

Posted on Dec 05, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is u-joint located and how can I check it?


front wheel drive or rear wheel drive .

Mar 05, 2016 | 2005 Pontiac Aztek

1 Answer

I have new rotors pads pins drums and shoes new michelin tires still have a vibration under braking 2004 camry 125k miles


check suspension rubbers and ball joints especially on the drive line end ( front drive --cv joints, ball joints , steering rod ends etc
rear end drive check for suspension movement that is allowing the drive line to change and causing problems with the "U" joints angles

Jun 07, 2015 | Cars & Trucks

1 Answer

Rear end jerk


Did check for broken spring.

Apr 24, 2013 | Cars & Trucks

1 Answer

Trying to change u-joints front and rear on driveshaft? any advice or assistance would be appreciated..


firt you will need to remove the drive shaft by un bolting it from the rear end. U joints are held in with a small clip on some, others have a cover which is bolted on over the end of the u joint. once you remove the clips or cover drive out u joint with a hammer replace with new one insert clips or cover install driveshaft greese all fittings.

Sep 01, 2011 | 2003 Ford F150 Regular Cab

1 Answer

Clunks wen u stop and go on the rear of my 99 chevy tahoe i allready change all of my breks and same thing


This happened to me. I had rear end replaced, springs, shocks and universal joints replaced and still same issue. I dropped drive shaft and greased the slip yolk going into transmission. Problem fixed. $4 grease cost me about $1500.
Dave

Apr 06, 2011 | 1999 Chevrolet Tahoe

1 Answer

Need to know how to drop a drive shaft to tow the 1999 Lincoln to go from Fla to Texas


You need to jack the back end up and place it on jack stands. then make a paint mark on the driveshaft and the rear end yoke, so when you put it back in, it will be "match marked" to the same spot. This is for proper balance. Then just unbolt the Ujoint from the rear yoke. Be sure to wrap something around the joint o the caps don't fall off the universal joint. Once it is loose from the rear end you can slide it out of the transmission. I would suggest covering the hole in the tranny also for transport. Some transmission fluid might come out of the rear when you remove the driveshaft.

Dec 31, 2010 | 1999 Lincoln Continental

1 Answer

There is a clanging noise when i put it in gear and can hear it while driving is it the rear end or universal joint


Check rear-end fluid level and play in rear pinion gear.
Check universal joints for play. If play is in pinion gear change rear end fluid and add a full bottle of LUCAS oil stabilizer, will quiet rear end noise.

Feb 01, 2010 | 2000 Chevrolet Silverado 1500

1 Answer

Sounds like a vibration from the rear end. how could I see if the rear end is the problem? I was thinking about jacking up the rear of the truck, (and of course using jack stands and blocking the wheels,...


thats a good start. also dont forget to chk your u-joints. while its in the air have someone put it in gear and slowly accelerate. if noise or vibration have them apply the brakes and see if problem decreases. most of the time though i have found a bad u-joint to be the problem and the only way to really chk it is to drop the rear of the drive shaft and make sure that the u-joints move freely with no slop

Nov 14, 2009 | 1996 Ford Ranger SuperCab

2 Answers

My 96 taho makes a noise


Change the U-joints on the rear drive shaft. They don't have to move to be bad. The bearing in the joints are rusted. Be sure to mark the yolks on your drive shaft and rear diff pinion. They are ballanced are must go back in the same way you took them apart.

With that being said, did you drop the shaft an dnot put it back in the right way? that will cause a vibration. Also, have you checked to see if there is any play in your pinion shaft?

Feb 17, 2009 | 1996 Chevrolet Tahoe

1 Answer

I need to disassemble a Ford 9" third member


Is this a 9" inch rear end? if so unbolt the axles from from the out side behind the brakes and pull them out, then remove the drive shaft rear u joint saddles and drop the drive shaft down, remove all the bolts from the differential carrier on the drive shaft side and drop out the rear end unit, be careful it is very heavy and the ring gear teeth can really cut u up.

Sep 29, 2008 | Ford F-150 Cars & Trucks

Not finding what you are looking for?
1990 Ford Thunderbird Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...