Question about 2007 Acura RDX

Open Question

How to remove door panel driver side 2010 rdx?

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

super_guy

  • 1986 Answers

SOURCE: RDX Front Door Panel Removal - instructions,

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2010 honda pilot driver side window will not go up


Driver side windows get the most use and so fail the most often. First test the switch, then remove door panel to test for current getting to the motor. If current is good, motor may have failed.

May 28, 2016 | 2010 Honda Pilot Touring

1 Answer

HOW DO YOU REMOVE DOOR PANLE DRIVER SIDE


Courtesy of expert Chuck Martin.
Snap out two door pull strap retaining screw covers. Remove screws.
Remove screws on front, rear and center of front door trim panel.
Using the Trim Pad Removing Tool or equivalent, pry the trim panel retaining clips from the door inner panel.
These are plastic so be careful you can use a pair of needle nose pliers if you don't have a trim tool.Just start at bottom of door panel and work your way around and up

Mar 09, 2016 | 2010 Lincoln MKZ

1 Answer

How do i fix a stuck blend door on 2010 dodge nitro?


I would pull off the blend door actuator and swap it out with a new one. Or another option is to swap it out with one of the other actuators. The blend door actuator is interchangeable with the actuators for the mode-air doors and the recirculation-air door.

Disconnect and isolate the negative battery cable.

If equipped, remove the silencer from below the driver side of the instrument panel.

Disconnect the wire harness connector from the blend door actuator located on the driver side of the air distribution housing.

Remove the two screws that secure the blend door actuator to the actuator mounting bracket and remove the actuator

Feb 17, 2015 | 2010 Dodge Nitro

1 Answer

How do I remove the drivers door panel on a 2010 chrysler town and country


remove all screws from the inside door panel around the handle and anywhere else then gently take a flat screw driver and start prying the door panel away from the door but be careful not to break the plastic clips on the inside of the door panel

Nov 02, 2014 | 2010 Chrysler Town and Country

1 Answer

Fuse panel box diagram for 2010 explorer sports trac


g06304730
F5 5 Rear window motor. Roof opening panel module. Auto-dimming interior mirror unit. Door lock switch, driver side. Door lock switch passenger side. Power window motor, driver side front. Overhead console switch assembly
Not sure if this is what you're looking for. Let me know if it works.

Jul 18, 2014 | 2010 Ford Explorer Sport Trac

1 Answer

How do you take the front driver side door panel off on 2010 hyundai elantra


It is pretty easy, but care must be taken so as to not damage the door panel. I recommend purchasing a door panel clip removal tool for this purpose. They are available at most parts retailers for just a few dollars. Using these tools to relaese the plastic clips on the door panel can save you a lot of aggravation and expense.

> Remove the triangular-shaped cover that covers the inside portion of the door mirror mountings. It simply "un-clips".

> Remove the screw that retains the bezel over the indide door release handle and remove the bezel.

Remove the two scres retaining the door panel to the door frame. One is under the triangle cover behind the mirror that you removed, and the other goes straight down into the pocket of the door pull.

Then use the special door clip release tool (recommended) or another suitable tool to pop the clips loose around the perimeter of the door panel. Lift out and up to remove door panel.

Installation is the reverse order.

May 28, 2012 | 2010 Hyundai Elantra

1 Answer

Air blend door jeep liberty 2010


My blend air door is stuck on my 2010 liberty. I have removed the actuator panel on the drivers side and the middle door that controls the air flow to the dash is completely seized. There are 4 blend air doors on this liberty, 2 control the heat/ac and 2 control the air flow.
there is no access to them from the drivers side and the passanger side looks like I have to cut into the air box to get to them.

Jan 03, 2012 | 2010 Jeep Liberty

1 Answer

RDX Front Door Panel Removal - instructions, schematics?


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Mar 18, 2009 | 2007 Acura RDX

Not finding what you are looking for?
2007 Acura RDX Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...