Question about 2002 Ford F250 Super Duty SuperCab

1 Answer

How many nm is 50 ft lbs - 2002 Ford F250 Super Duty SuperCab

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 39 Answers

67.7908974165944 nm
i found this link hope it helps
cheers paul Convert newton meters to foot pounds Conversion of Measurement Units

Posted on Jul 11, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why head bolts torque are different from 2003 and 2005 1.8 nissan sentra?


I have never seen a code specifically identifying a blown head gasket. I checked the service manual and the procedure is the same.

4. Tighten cylinder head bolts (1) to (10) in numerical order as shown in 5 steps. Cylinder head bolts Step 1: 29.4 Nm (3.0 kg-m, 22 ft. lbs.) Step 2: 58,8 Nm (6.0 kg-m, 43 ft. lbs.) Step 3: 0 Nm (0 kg-m, 0 ft. lbs.) (loosen) Step 4: 27.4 - 31.4 Nm (2.8 - 3.2 kg-m, 21 - 23 ft. lbs.) Step 5: 50° - 55° (target: 50°) clockwise
images-xozrttqlr3qpoa0t2tmccx0o-1-0.png To confirm it is a head gasket, do a compression and/or leak down test. Wouldn't hurt to pressure test your cooling system as well.

Apr 16, 2017 | Nissan Cars & Trucks

1 Answer

What are cylinder head torque specs?


Tighten the cylinder head bolts in the sequence shown in figure. Using the 4 step torque turn method, tighten according to the following values.
  1. Tighten center fasteners 1 thru 6 to 33 Nm (25 ft. lbs.) . Then outer fasteners 7 thru 10 to 27 Nm (20 ft. lbs.) .
  2. Tighten center fasteners 1 thru 6 to 67 Nm (50 ft. lbs.) . Then outer fasteners 7 thru 10 to 27 Nm (20 ft. lbs.) .
  3. Tighten center fasteners 1 thru 6 to 67 Nm (50 ft. lbs.) . Then outer fasteners 7 thru 10 to 27 Nm (20 ft. lbs. ).



26083805-2jaahwjhyda0eguw15ciywpg-3-0.gif

Then tighten all fasteners 1 thru 10 90°turn . Do not use a torque wrench for this step.



26083805-2jaahwjhyda0eguw15ciywpg-3-2.gif

Feb 06, 2016 | 1999 Mitsubishi Eclipse

1 Answer

Show picture of how to put alternator on 2.2 s10


This answer is in a previous question; just keep in mind this procedure to install:
  1. Position the alternator in the vehicle and loosely install the retaining bolts.
  2. On 1994-98 models, tighten the top alternator bolt to 22 ft. lbs. (30 Nm) and the bottom bolt to 32 ft. lbs. (43 Nm).
  3. On 1999-99 models, tighten the rear bolt to 37 ft. lbs. (50 Nm) and the front bolt to 18 ft. lbs. (25 Nm).
  4. On 1994-98 models, install the alternator brace, then tighten the retaining nut(s) and bolts to 22 ft. lbs. (30 Nm).
  5. On 1999-99 models, install the alternator brace, tighten the brace-to-alternator and brace-to-intake retainers to 18 ft. lbs. (25 Nm). Tighten the brace-to-engine stud nut to 37 ft. lbs. (50 Nm).
  6. Install the battery terminal wire and tighten the retaining nut, then engage the alternator wiring connector.
  7. Hold the serpentine drive belt tensioner, back off the belt while slipping the belt over the alternator pulley. Gradually lower the tensioner into contact with the belt, then check for proper alignment and tension.
  8. Connect the negative battery cable.





Previous question link HERE.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 21, 2012 | Cars & Trucks

1 Answer

Need torque specs on axle nuts for dana 50 rear axle


Dana 50 Front Axle

Observe the following torques;

* Left and Right drive axles-to-cross member: 120-150 ft. lbs. (163-203 Nm)

* Axle arm-to-radius arm: 180-240 ft. lbs. (244-325 Nm)

* Coil spring insulator: 30-70 ft. lbs. (41-95 Nm)

* Upper spring retainer: 13-18 ft. lbs. (18-24 Nm)

-----------------------------------------------

Dana 60 Front Axle

Observe the following torques;

* Drive shaft-to-flange: 15-20 ft. lbs. (20-27 Nm)

* Track bar nut and bolt: 160-200 ft. lbs. (217-271 Nm)

* Stabilizer link nut: 20-30 ft. lbs. (27-41 Nm)

* Stabilizer barU-bolt: 50-65 ft. lbs. (68-88 Nm)

* Spindle connecting rod-to-knuckle: 70-100 ft. lbs. (95-136 Nm)

* Front spring U-bolt: 95-100 ft. lbs. (115-135)

Feb 19, 2011 | 1986 Ford F 250

1 Answer

Can you tell me the torque spec.on head bolts for a 1985 ltd 3.8 thank you


Six IN LINE - 6L

zjlimited_510.jpg

Fig.: Cylinder head torque sequence - 6 -cylinder engine



Cylinder head torquing should proceed in three steps and in the prescribed order. Tighten them first to 50-55 ft. lbs. (65-71 Nm), then give them a second tightening to 60-65 ft. lbs. (78-84 Nm). The final step is to 70-75 ft. lbs. (91-97 Nm), at which they should remain undisturbed.


Six IN V - 6V

zjlimited_511.jpg

Fig.: Cylinder head bolt torque sequence - 6 -cylinder engine

Tighten the head, according to the illustrated sequence in three progressive steps. Tighten the bolts to 50-55 ft. lbs. (68-74 Nm), then 60-65 ft. lbs. (81-88 Nm) and finally to 75 ft. lbs. (102 Nm).


Hope this helps (remember to rate and commene this answer).

Jan 19, 2011 | 1985 Ford LTD

1 Answer

Looking for head bolt troque spec for 3.4l impala sfi04


Please don't forget to rate. Thank you:

Left side front cylinder head


98e175a.gif
Cylinder head bolt torque sequence-3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence-3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Nov 26, 2010 | 2004 Chevrolet Impala

    2 Answers

    It is hard to turn on both sides how do i change my steering pump


    Have you checked the fluid level and belt tightness?
    It is easy to change the pump.
    There is the small high pressure hose and the larger return hose, a pivot bolt, and the adjustable hold down bolt.

    Aug 13, 2010 | 1998 GMC Sierra

    2 Answers

    Head gasket torque specifications and sequense


    Please don't forget to rate. Thank you:

    Left side front cylinder head


    98e175a.gif
    Cylinder head bolt torque sequence—3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence—3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Mar 06, 2010 | 2001 Chevrolet Venture

    2 Answers

    I need rocker torque for 2003 pontiac with 3.1liter


    Left side:

    To install:
    1. Lubricate all the valvetrain components with engine oil.
    2. Install or connect the following:
      • Pushrods and the rocker arms and tighten the bolts to 14 ft. lbs. (19 Nm) plus 30 degrees
      • Rocker arm cover using a new gasket and tighten the rocker cover bolts to 89 inch lbs. (10 Nm)
      • PCV valve to the rocker arm cover
      • Coolant tube with the thermostat bypass hose and tighten the bolt to 98 inch lbs. (11 Nm) and the nut to 18 ft. lbs. (25 Nm)
      • AIR check valve pipe and torque the adapters to 22 ft. lbs. (30 Nm)
      • Engine mount strut and torque the bolt to 35 ft. lbs. (48 Nm)
      • Spark plug wires
      • Negative battery cable
    Right side:

    To install:
    1. Lubricate all the valve train components with engine oil.
    2. Install or connect the following:
      • Pushrods and the rocker arms and tighten the bolts to 14 ft. lbs. (19 Nm) plus 30 degrees
      • Rocker arm cover using a new gasket and tighten the rocker cover bolts to 89 inch lbs. (10 Nm)
      • Power brake booster vacuum pipe to the plenum
      • EVAP solenoid and ignition coil assembly
      • Spark plug wires
      • Alternator bracket and torque the bolts to 37 ft. lbs. (50 Nm)
      • Alternator and torque the bolts to 37 ft. lbs. (50 Nm)
      • Accessory drive belt
      • Negative battery cable
    3. Start the vehicle and verify no leaks.

    Feb 06, 2010 | 2003 Pontiac Grand Prix

    1 Answer

    2000 2.0 petrol pt cruiser head bolt torque?


    Use a torque wrench to tighten the bolts in the following order:
    1. Tighten all center bolts to 34 Nm (25 ft.-lbs.).
    2. Tighten the four corner bolts to 27 Nm (20 ft.-lbs.).
    3. Tighten all center bolts to 68 Nm (50 ft.-lbs.).
    4. Tighten the four corner bolts to 47 Nm (35 ft.-lbs.).
    5. Retighten all bolts a second time to the same specifications in step 4 to double-check torque.
    6. Finish by tightening all bolts an additional 1/4 turn.

    Nov 11, 2009 | 2001 Chrysler PT Cruiser

    Not finding what you are looking for?
    2002 Ford F250 Super Duty SuperCab Logo

    72 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    Marvin
    Marvin

    Level 3 Expert

    85206 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22484 Answers

    gerry bissi

    Level 3 Expert

    4388 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...