Question about 2001 Ford Taurus

Open Question

How to replace oil pump in transmisson 2001 ford taurus

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: Spark plug firing order Ford Taurus 2001

1-4-2-5-3-6

Posted on Apr 08, 2009

Ad
abauto
  • 353 Answers

SOURCE: How to replace my 2001 ford taurus fuel pump

2001 Ford Taurus V6-3.0L DOHC VIN S
Fuel Pump: Service and Repair

REMOVAL
1. Remove the fuel tank.
2. Clean the area around the fuel pump mounting flange.
3. Using the special tool, remove the fuel module retaining ring.(Screwdriver and hammer)
4. Remove the fuel delivery module from the fuel tank.
CAUTION: The fuel delivery module must be handled carefully to avoid damage to the float arm, filter, and convolute hoses.
INSTALLATION
1. To install, reverse the removal procedure.
NOTE: A stop should be felt when aligning the raised arrow on top of the fuel tank delivery module to the dot on the fuel tank.

Posted on Sep 08, 2009

Testimonial: "Very helpfull, except i think I installed it wrong because its doing the same thing, Fuel gauge is not working properly, I did not notice any arrows o"

c17hydro
  • 2989 Answers

SOURCE: how to replace a water pump on a 2001 ford taurus

This is for a 3.0L and VIN S engine--

VIN U Engine

  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Accessory drive belt and tensioner
    • Water pump pulley
    • Heater hose
    • Engine control sensor wiring
    • Water pump
54afbf0.gif
To install:
NOTE The water pump bolts are of different lengths and must be installed in the correct locations.

  1. Install the water pump. Tighten bolts 1, 2, 3, 4, 5, 6, 7, 8, 9 and 15 to 15–22 ft. lbs. (20–30 Nm). Tighten bolts 10, 11, 12, 13 and 14 to 72–106 inch lbs. (8–12 Nm). Refer to the accompanying illustration for the bolt locations.
  2. Install or connect the following:
    • Engine control sensor wiring
    • Heater hose
    • Water pump pulley and tighten the bolts to 15–22 ft. lbs. (20–30 Nm)
    • Accessory drive belt and tensioner
    • Negative battery cable
  3. Fill the cooling system and check for leaks

Posted on Dec 08, 2009

  • 1149 Answers

SOURCE: I need a replacement keys for 2001 ford taurus

A good place to start is a ford dealer. Often they can cut you a key off the VIN number. You will have to go there in person., and some kind of proof of ownership would be needed!

Posted on Apr 02, 2010

csmock132
  • 4669 Answers

SOURCE: 2001 ford taurus 3.0 liter ohv serpentine belt

3.0 OHV Vin U24dba77.gif

Posted on Apr 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace oil pump in transmisson


Remove the transmission from the vehicle. Disassemble the side of the transmission and replace the pump. Reassemble and re-install. HUGE project

Mar 31, 2018 | Ford Cars & Trucks

2 Answers

Where Is The Oil Pump Located>? And How Do I Replace The Oil Pump


Here you go. BIG Job!

http://www.ehow.com/how_4506339_replace-oil-pump-ford-taurus.html

The oil pump is an essential piece of equipment that keeps your Ford Taurus running. It lubricates the engine by keeping the oil circulating. Without this lubrication, the engine wouldn't run. An oil pump is usually located in the oil pan. If you want to change the oil pump and replace it with a new one, roll up your sleeves and get ready for some dirty work.

How to Check if an Oil Pump Is Bad

Things You'll Need




  • Wrench



  • New oil pump



  • New A/C bolts

Remove Old Oil Pump


  1. Drive your Ford Taurus up onto ramps or lifts so you have room to work as you pull out the oil pump. You could also use a jack, but make sure you brace the front wheels so they don't roll. In addition, set the emergency break firmly into position so the car doesn't roll.


  2. Take the engine out and put it on an engine stand then remove the upper intake manifold. Take off the valve covers then the accessory drive belt.


  3. Remove the power steering pump and the alternator. The water pump is the next component to remove, followed by the A/C compressor and bracket.


  4. Rotate the pulley shaft clockwise to remove the crankshaft pulley. It has left-handed threads.

  5. Pull out the oil pan and the oil pump screen and tube. Take off the front cover and the timing chains and remove the crankshaft timing gears. Finally, remove the oil pump, taking note of the bolts you removed and in which order you remove them.

Insert New Oil Pump


  1. Install the new oil pump and put the bolts back on in the same manner you removed them. Tighten these bolts to 71 to 106 in-lb.


  2. Reinsert the crankshaft timing gears, timing chains and front cover. Put the oil pump screen and tube back on, torquing the bolts to 71 to 106 in-lb, and torque the nut to 15 to 22 ft-lb.

  3. Put the oil pan back in, then the crankshaft pulley. Install the A/C compressor and bracket using new bolts for the A/C. Add the water pump, alternator, power steering pump, the accessory drive belt, valve covers and upper intake manifold.


  4. Replace the engine back into your Ford Taurus and fill the crankcase. Start your engine and look for leaks in the area you were working.

Read more : http://www.ehow.com/how_4506339_replace-oil-pump-ford-taurus.html

Aug 06, 2015 | 2004 Ford Taurus

1 Answer

Oil sending unit 2001 ford taurus


On most engines it is on the driver side of the block under the master cylinder.

Jan 25, 2013 | 2001 Ford Taurus

1 Answer

How do I change a 2001 ford taurus timing chain cover gasket?


Pretty tough job,,if you dont work on cars much..You have to remove the water pump,,and also alot of the accessories around the water pump..You also have to drop the front of the oil pan down ,,to remove the timing cover..I always like to remove the oil pan and replace the gasket on it as well...

Oct 14, 2011 | 2001 Ford Taurus

1 Answer

I need to know where the oil pump is located on a 2001 ford taurus se 3.0 ohv is it inside or outside the engine


Hello bigivy69,

The oil pump is inside the oil pan. See picture below.

netvan_80.png

Regards,
netvan

Apr 09, 2011 | 2001 Ford Taurus

1 Answer

How to change the oil pump out in ford taurus


It matters if the 8th digit of vin numbers is a U or an S.
For a U: Remove oil pan, remove oil pump retaining bolts, oil pump and shaft.
For a S: You will have to remove the oil pan, front cover, the timing chain, and the crank shaft sprocket to get to the oil pump

Mar 07, 2011 | 2001 Ford Taurus

2 Answers

I hav 2001 ford taurus 3.0 single head cam engine makes noise , mechanic said that oil pressure is low n need change oil pump. but oil light not comes on always, it becames on only driving, when I...


That sounds like a pump... the oil pump is inside of the engine. You need to drop the oil pan to gain access - however, you will need to pull the motor to do that.

Jan 25, 2011 | 2001 Ford Taurus

1 Answer

Replaced oil pump and main bearings but still have low oil pressure on a2001 ford taurus vin u


Replace the oil sending unit that sends the signal to the gage in the car. Located on the side of the motor.

Feb 09, 2010 | 2001 Ford Taurus

1 Answer

Where is the vent for the transmisson on a 2001 Ford Taurus


the vent would be located on the top of the transmission small round floating button shaped part.

Dec 01, 2009 | 2001 Ford Taurus

2 Answers

Intermittent fuel pump engagement when turning key - 2001 Taurus


try cleaning the connector that goes to the fuel pump, sometimes they corrode on inside. If that does not fix, test the wires feeding fuel pump with a multi meter until the condition shows itself again, if voltage drops to zero or very low then wiring problem, if voltage is unchanged with problem and fuel pump is not working and connectors are all clean, try replacement of fuel pump.

Oct 09, 2009 | 2001 Ford Taurus

Not finding what you are looking for?
2001 Ford Taurus Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...