Question about 2007 Ford Edge SEL Plus

1 Answer

2007 Ford Edge SLE plus No heat on driver side. But passenger side does. Blend door actuator is moving though

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,256 Answers

Do you have separate heat/cooling controls for driver and passenger. If so, you have two blend doors/actuators.

Posted on Jan 12, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
michael_grey
  • 365 Answers

SOURCE: cold air on passenger side warm air on drivers side

Actuator motors either get a tear in the rubber or a hose is broken and not letting vacuum assist in its opening.
You can try moving the lever by hand and see if the air gets colder on the bad side.c976077.jpg

Posted on Aug 04, 2009

dnewcombe1
  • 1564 Answers

SOURCE: Air Blend Actuator not working

Make sure you are getting plenty of vacuum to the control, if you are than it will have to be replaced.

Posted on Sep 05, 2009

roniecon
  • 6927 Answers

SOURCE: need to locate blend door actuator on 2002 ford

Open the glove box,and look on top of ac/heater box toward the center of vehicle,it should be setting right there.

Posted on Oct 10, 2009

  • 248 Answers

SOURCE: What do I have to remove to access blend door actuator

very lenghty process. too long to describe here....go to Bonneville Forums read the text and follow linked there at the bottom....very good and detailed....I'm doing that right now,,,,it is a bugger,

Posted on Apr 16, 2010

  • 2591 Answers

SOURCE: The driver side only blows

Yes it is most likely a vacuum actuator there are more then one . They open and close little doors in the ducts to deriect air flow inside the ducts . They are not easy to get at in most cases however you should look at all vacuum lines going to and near the unit its controlled by engine vacuum . exhust all other opptions first before takeing the dash out . The problem could also be electrical check the control switches make sure the switch is not bad on one side . Spend some time looking and thinking before you start riping things apart. Good luck with it

Posted on Sep 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2007 ford 500 front heater passenger side cold Wright side hot full anti no air block?


That would be problem with the passenger side blend door actuator or a binding blend door. Usually a bad actuator.

Nov 29, 2017 | Ford Cars & Trucks

1 Answer

Location of passenger side blend door actuator on 2006 mercury mountaineer auto controls, 6 cylinder


Temperature Blend Door Actuator - RH, EATC Removal and Installation
  1. Remove the RH floor console finish panel.
  1. Lower the glove compartment.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  2. Remove the 3 RH temperature blend door actuator screws.
    1. Remove the RH temperature blend door actuator.
2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

Jun 19, 2017 | Mercury Cars & Trucks

1 Answer

Heat on driver side not on passenger 2007 Sebring


If you have a dual range heating system (separate settings for driver and passenger), your blend door actuator for the passenger side is not working. I have no idea on how hard it is to get to this actuator on your particular vehicle, but know that it's under the dash on the passenger side, and may be quite involved in troubleshooting and replacing if necessary.

Jan 07, 2017 | 2007 Chrysler Sebring

1 Answer

Lost of heating after 40 minutes of driving.


You have a dual range HVAC system. It has two blend doors in the HVAC box, and only the blend door for the driver's side is working properly. You will have to troubleshoot, and possibly replace the blend door actuator for the passenger side.

Jan 01, 2017 | 2006 Ford Explorer Eddie Bauer 4x4

1 Answer

2011 Ford Flex. Driver side blows heat but the passage side blows cold air. Think it has some to do with the blend door. Assuming it is duck open. Priblem? Where is it located, how to fix it.


It will be the passenger side blend door actuator. Remove the glove box and if you were sitting in the passenger seat it will be by your left knee. Unplug and remove the screws then install new one, it is a little tight inside there though.

Jan 03, 2016 | Ford Cars & Trucks

1 Answer

Location of blend door actuator,2007 ford tauris


Drivers side, under the dash, to the right of the gas pedal. If you have dual control there is one on the passenger side also.

May 10, 2015 | 2007 Ford Taurus

1 Answer

Heater blows hot on passenger side and at same time blows colder on driver side. what can i do to fix this problem


if its equipped with the dual climate knobs where you can set the heat to suit yourself on either side, you have an actuator, or an actuator door hanging up that operates the drivers side vents.

Dec 04, 2010 | 2007 Ford Edge SEL Plus

2 Answers

AC blows hot air on the driver side and cold air on the passenger side


You may have a bad temperature door actuator motor on the drivers side. The actuator is what moves the temperature blend door and when it fails it usually moves the door all the way to the "hot" position. Sometimes if you shut the vehicle off for a bit then restart it the system will work fine for a while then the actuator will again swing the door all the way open or shut. I've replaced several of these actuators [both drivers side and passenger side] for similar problems.

Jul 08, 2010 | 2005 Chevrolet Silverado

4 Answers

The heater in my 2003 Dodge Ram 4x4 will not heat up or gets only luke warm & only on the passenger side....any suggestions?


Cold on drivers side and heat on passengers side, actuators working properly and blend doors are moving. Heatertreater is for piece of plastic on actuator motor. I moved blend door by hand after disconnecting actuator and works fine, both sides freezing when moved in opposite direction.

Dec 04, 2009 | 2004 Dodge Ram 1500

2 Answers

2004 chevy avalanche with dual control system problem


this problem is caused in almost all cases by a failed actuator that moves the door insiode the heating/ac duct to change the outlet temperature, it is called the Air Temperature Control Blend Door actuator.

Oct 05, 2009 | 2004 GMC Envoy

Not finding what you are looking for?
2007 Ford Edge SEL Plus Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...