Question about Acura Cars & Trucks
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Look for the end of the wire retainer clip. Unhook it and lift it up. Remember not to touch the bulb. But if you do, just clean it with a bit of alcohol.
btw - Here's a bit of info from a previous post of mine...
The low beams consist of three parts. The bulb, inverter/ballast and the ignitor. The bulbs usually start to loose their color long before they burn out. The inverters/ballasts either go out after a while or take a while to start up.
Before you spend money on a new bulb, try swapping it with the one on the other side. You'll need a security torx screwdriver to get the covers off of the back of the lights. Don't touch the glass bulbs. If you do, just clean them with a bit of alcohol.
If the problem stays on that side, try swapping the ignitors. They're mounted inside the black covers.
If the problem is still on that side you've got a bad inverter. They're mounted on the bottom of the headlight assembly. You'll need to remove the front bumper and remove the headlight assembly to get to it. (I recommend you take pictures as you remove things so can put them back together correctly.)
Posted on Jan 05, 2009
Follow this link. There is detailed step-by-step info here
Please kindly let me know if it works for you
Posted on Jan 31, 2009
This starter can be changed without disassembling the top of the engine on the 2.5 with automatic transmission. You will need a 10mm, 14 mm, 17mm, and a 9mm wrench. First with any electrical repair disconnect the battery at the negative terminal. The starter is on the driver's side close to the firewall below the intake manifold. Remove the transmission dip stick so you don't ruin it, then look and study the starter itself. You will notice the starter drive housing with a top and bottom bolt. The top bolt is a 14mm and the bottom a 17mm, loosen both a half turn. Remove the top 14mm bolt first, then the bottom 17mm, this will allow you to pull the starter out of the bell housing. With some angling and no brackets holding the back of the starter you should be able to pull it out enough to disconnect the positive wire and 9mm nut from the soleniod. Disconnect the starter ignition small wire by pulling it off it's connector. Now just pull it out of the engine and fender void and you've got it, saving about a hundred and fifty dollars of labor. Take it to the parts house and match it up with a well made remanufactured or new starter. Reverse the proceedure, hook up the battery.
Posted on Mar 19, 2009
your car could still be under warranty depending on the miles the car have call your Acura dealer for info. I had my transmission replaced in Feb 09 and it was done for FREE!!
Posted on Aug 07, 2009
Tips for a great answer:
Jan 08, 2016 | 1998 Acura CL
Nov 28, 2014 | Mercedes-Benz C-Class Cars & Trucks
Feb 27, 2011 | 1996 Ford Explorer
Apr 01, 2010 | 1996 Ford Explorer
Jan 31, 2010 | 2000 Acura TL
Sep 16, 2009 | 2009 Acura TL
Sep 09, 2009 | Acura Cars & Trucks
Apr 21, 2009 | 2004 Acura TL
Mar 22, 2009 | 1996 Acura TL Series
Nov 26, 2008 | 2006 Honda Accord
May 11, 2019 | Acura Cars & Trucks
18 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: