Question about 2004 Scion xB

1 Answer

In what position does the thermostat go in the housing on a2004 scion xb

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Scion Master
  • 24,425 Answers

Same way the old one came out

Posted on May 16, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 255 Answers

SOURCE: scion xb wont start

Hi.. Yes i fix my problem by disconecting the neutral suitch and reconecting it ,,they get dirty with time and dont make contact ,Is a good idea to disconect and clean as many contacts as you can and put some special grease on them to prevent other problems ...

Posted on Jul 29, 2008

  • 101 Answers

SOURCE: need help to remove 2005 Scion xB water pump

1st ...that should be covered under 6 year 50k power train warranty from the dealer.
But if your over....you need to unbolt the right side motor mount (on the water pump side) and lift the engine some with a floor jack to get clearance,

Posted on Apr 11, 2009

  • 439 Answers

SOURCE: How d you replace the starter on a 2005 Scion xb?

There are two bolts, one is at the top exactly opposite of the first one you took out. You will not be able to see it, but feel around the head of the starter where it goes into the block and you will feel where it goes.

Posted on Jun 23, 2009

  • 38 Answers

SOURCE: How do I install alt. belt on 2005 scion xb?

I just looked at my '04 xB. It looks very straight forward.
loosen the bolt that holds the alternator to the bracket.
carefully slide the alt to the bottom. (Also be aware of the plug and wires on the alt.They should never hold the weight of the alternator. You dont want them breaking prematurely.)
Pull the belt off, remove the belt from the crank shaft pulley.

Do the reverse, and you will have replaced the belt.

Make sure to check the belt in about a week or so.
New belts will stretch over time. Make sure you keep the tension tight enough to work correctly, but not so tight that the alernator shaft is warped.
I usually place the new belt on both pulleys and give a good "medium" pull on the alt while tightening. Find the middle of the belt and squeeze them together, depending on the type and length of the belt, there should be about 1/4" of flex on both sides.

Posted on Jun 29, 2009

polarcycle
  • 1392 Answers

SOURCE: 2005 scion xb window quit

Sounds like a stuck motor. Hold the switch down and slam the door shut. This will usually break it free. It will most likely need a motor though.

Posted on Jul 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i access the top starter mounting bolt on a scion xb 2005


you have to remove the flywheel housing side cover

Feb 18, 2017 | 2005 Scion xB

2 Answers

Remote starter only allows my starter to turn over twice; needs at least 3 with my key. How to adjust to have it starter run longer on remote?


I know you are looking to have the remote starter run a third time but I would say you need to look at your Fuel Pressure Regulator on the Scion. Sounds like it is not holding fuel pressure at the fuel rail and that is why it requires a third Crank

Jan 05, 2016 | 2006 Scion xB

1 Answer

Scion XB automatic door lock, driver's door not working with remote. How do I reset it?


This is a common problem on the Scion XB, replace the drivers door lock actuator and you should be fine.

May 19, 2011 | 2005 Scion xB

1 Answer

I have a 2006 Scion xb with a code p0010. I changed the camshaft timing oil control valve but the light is still on. Can anyone help?


P0010 Scion P0010 Scion - Camshaft Position 'A' Actuator Circuit Bank 1 pdf.gif [img alt="Share Code" src="http://7ff587e0977842abc470-bfcce390d0a24108a1dce58e5acfca1f.r31.cf1.rackcdn.com/share.png"> 0 [img alt="P0010 Scion Comments" src="http://7ff587e0977842abc470-bfcce390d0a24108a1dce58e5acfca1f.r31.cf1.rackcdn.com/comments.png"> ' Add Comment - Dirty Oil
- Variable Valve Timing (VVT) circuit is open or shorted
- Oil Control Valve (OCV) circuit is open or shorted
- Faulty variable valve timing (VVT)
- Faulty oil control valve (OCV)
- Damaged ECM


Read more: http://engine-codes.com/p0010_scion.html#ixzz3LSVT0h8C

Dec 13, 2010 | 2004 Scion xB

1 Answer

SCION XB CAMSHAFT POSITION SENSOR P0010 CAME ON WHEN CHANGING BEL


Trace your steps, look for the sensor wire or plug that connects the sensor to your harness, you may have unplugged it, or damaged it.

Jan 01, 2010 | 2004 Scion xB

1 Answer

How to replace tail light housing


for the most part you open the rear hatch and remove the panel and then you can see the small nuts or screws you need to remove to get it out try these websites www.autozone.com and www.alldatadiy.com if all fails stop by your local Scion dealership in the parts department and they will print you out a some pictures and diagrams wish you the best of luck Michigan.

Nov 13, 2009 | 2006 Scion xB

Not finding what you are looking for?
2004 Scion xB Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Scion Experts

Jonah Oneal

Level 3 Expert

14092 Answers

Marvin
Marvin

Level 3 Expert

84625 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Scion Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...