Question about 2006 Mitsubishi Outlander
If the cause of the problem is fixed, the light will go out by itself. If you haven't fixed the underlying problem, the light will stay on. You can clear the codes with a scan tool, but it'll come right back on the instant you turn the ign key.
Posted on Jun 07, 2019
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: 1999 Alero anti lock brake light
u can have the light scanned by autozone free of charge. Also in new york state the anti lock system is not part of inspection and can not be a failable issue. Ofcourse your state may be differant. Also the abs light will not turn on for brake pads.. Most common on the olds alero is a bad wheel bearing. The abs sensor is built into all the wheel bearings. The code that u can get out of the car will even tell you what wheel it is that is causing he light to come on. Unless ofcourse its not a wheel bearing and its a internal abs system issue. Let me know what the code is and I will try to get you a pinpoint place to look....
Posted on Aug 29, 2008
i recently had this problem too, except i had all the lights on (ABS, service vehicle, trac-off, AND service engine) they are all easy to fix without spending more than 20-30$ for labour (depending how much your mechanic charges you) mine did it for free and he found out why the engine light is on afterwards too. so to fix all these lights (abs, trac-off, and service vehicle you MUST get another ABS cable (i went to a garage, they were towing a GM vehicle to the junk yard so i grabbed some scissors and cut BOTH abs cables on each side (good thing i did because one was bad) and braught them to my mechanic. the reason the lights come on is probably a defect or in my case my mechanic said it was salt buildup in the wires (on the drivers side) so he cut the wire off and rewired the new one and BOOM all the lights came off (service vehicle, abs, and trac-off) now for my service engine it says catalytic converter but im trying to put some fuel system cleaner to help it out i read somewhere that this is a defect of the car, so if you dont have that light yet, SELL your car ASAP for as much as you can get for it (after fixing the lights of course) and always google (car name+recalls) in the search bar to see what youre getting into, take care
Posted on Jun 15, 2009
Check the fluid level, top it off if needed, look for a fill to line on the side of the reservoir. Check rear brake shoes/pads, are they too worn? Replace with new ones. Bleed all 4 wheels, starting with the farthest one, then go to next farthest, and so on. Look for leaks inside the rear wheels. Adjust rear brakes (if shoes not pads).
Posted on Aug 26, 2009
Turn the key off.
Press the "Info" button on the left of the dash cluster until your maintenance miles/months screen is displayed.
Press and hold the "info" button until the maintenance screen begins flashing.
Release the "info" button and then push and hold it it for one second.
Your Maintenance intervals should reset to +6 months and +7500 miles since the last interval amount.
Note that if you have not reset it for more than one interval, you may need to do it more than once. If you have not done it for many intervals, you may need to have it reset with the scantool at a dealer, as I have run into a handful of vehicles that the oil change reminder locked up after 3-4 "intervals" were skipped/not reset.
Posted on Sep 11, 2009
Tips for a great answer:
Sep 16, 2015 | 2008 Mitsubishi Endeavor LS
Jan 28, 2012 | 2006 Mitsubishi Outlander
Dec 22, 2011 | 2002 Mitsubishi Montero
Feb 27, 2011 | 2006 Mitsubishi Outlander
May 12, 2010 | 2006 Mitsubishi Outlander
Feb 24, 2010 | 2006 Mitsubishi Outlander
Oct 07, 2009 | 2006 Mitsubishi Outlander
29 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: