Question about 2000 Chevrolet Silverado 1500

1 Answer

The door lock is crazy I lock the car and automatically it unlock

Today, when I lock the car it not want to respond the door to lock and unlock then when i closed the door sometimes the part that say that is lock and unlock the door appear it suppose locked but is unlocked because when I lock the car the thing that tell you that is locked in fist is locked but when I loose the button of locked the car returns to unlocked and that was my problem

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 5,736 Answers

What ????????????

Posted on Aug 29, 2017

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 2 Answers

SOURCE: sliding doors won't lock or unlock using keyless.

there are 3 possibilities that I would check first. 1: make sure the contacts on the door, and body where the touch are clean. the lock and unlock signal are sent through these. 2: You may try replacing the battery in your key fob. 3: the power lock motors may have gone bad. To check, lock the doors with the drivers door panel, if they lock, they are fine. Another solution may be to recode your key fob. procedure for coding the fob to your vehicle can be found online.

Posted on Dec 18, 2008

Anonymous

  • 206 Answers

SOURCE: Automatic door locks / 2001 Chevy Suburban

Your book should give you program options for the door locks If your fob wont work either you got a relay for the door lock bad it is located in the fuse panel push the door lock button and find the one that is clicking

Posted on Apr 12, 2009

Anonymous

  • 68 Answers

SOURCE: 2008 chevy malibu. cannot unlock doors from dirver

Intermittent door ajar switch contacts.

Posted on Mar 05, 2010

2coolrick

Cool Blue Services

  • 560 Answers

SOURCE: 2008 chevrolet malibu door lock problem

You have a intermittent condition. To isolate the cause: 1.Disconnect the drivers door lock/unlock switch from the connector. Drive the vehicle and see if your random lock/unlock condition has stopped. If it has, replace the switch. If it hasn't:
2. You have a grounding problem or a problem in the BCM (Body Control Module) and should have a technician use a Tech 2 Diagnostic Link Tool to access the BCM computer to obtain any fault code data to help correct the condition.

Posted on Mar 07, 2010

Deano

  • 248 Answers

SOURCE: key fob will not activate anything. can't

I too had this problem. I finally found out that my problem was the result of the metal contacts that touch the circuit board when you push the buttons had worn out. To correct my problem, I purchased a small pad that slides right inside the remote and fixes all the buttons. Since then, my remote has worked problem free for the past 3 months. The company that makes the pads is KEYLESSFIX. The following link will take you to the actual website:

http://www.keylessfix.com/keylessfixcom/

Please remember to rate my solution. Thanks!

Posted on Feb 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power lock


check door locks fuses and relays.if all is good and you cant operate door lock buttons manually problem could be in the generic electronic module.if door locks dont work from the remote battery could be dead in remote transmitter.try to reset door locks control module first obtain all remote transmitter.sit inside vechicle with all doors closed.switch ignition from off to on 8 times in 10 seconds. doors should lock then unlock.when this procedure works then press any button on any of the remote transmitter doors should lock and unlock.if all fails let dealership fix..

Dec 27, 2012 | 1998 Ford Windstar

1 Answer

2003 Dodge caravan sport. First, the passenger sliding door lock was not responding to lock and unlock. Only intermittantly. Now, the driver sliding door is copying it. Sometimes, only one does it, th


No, not so strange. - Happens a LOT. Sometimes you can get them working again by cleaning the electrical contacts that are on the front edge of the door and their mating contacts on the "B" pillar area. If cleaning the contacts does not get them working again, then you most likely need to replace the door lock actuators inside the doors.

Apr 19, 2012 | Dodge Caravan Cars & Trucks

1 Answer

I have a 2005 Ford Focus. The anti theft system was locked accidentally. How can I unlock the system.


If you dont have a key fob you could probably do it this way. Open the driver's door, get in the vehicle and close the door, open the driver's window and lock the door with the key. Then unlock the door manualy from inside the car this should trigger the antitheft alarm. Close the door and cycle the key to lock and unlock the door. This sometimes works

Jun 08, 2011 | Ford Focus Cars & Trucks

2 Answers

I have a 98 GMC JIMMY. Remotes and Dome Lights stopped working. Car would start then immediately die. Took it to the dealer and they stated it was the Body Control Modual (BMC). Picked up the vehicle...


Keyless Entry System Circuit Description
The Power Door Locks/Remote Keyless Entry control system provides several functions. The driver operates the vehicle door locks and rear window release from outside the vehicle using a hand-held radio transmitter. The transmitter sends coded signals to the remote control door lock receiver. The remote control door lock receiver detects and decodes the signal from the transmitter. The remote control door lock receiver issues signals to the body control module (BCM) through a serial data link. The BCM actuates relays to lock and unlock the doors and liftgate. The BCM can also release the liftglass. The power door lock switches provide manual control of the door locks.


Transmitter Programming
Important: Different keyless entry systems are used on General Motors vehicles. The parts are not interchangeable even though the parts may appear to be similar. Observe the back of the transmitter in order to properly identify the system. On 1998 S/T pickups and utilities, use a transmitter identified with GM/UTA preceding the part number.
With the driver door closed, hold down the power unlock button on the door panel.
Turn the ignition switch to the ON position.
Turn the ignition switch to the OFF position.
Turn the ignition switch to the ON position.
Turn the ignition switch to the OFF position.
Release the power unlock button on the door panel.
The remote control door lock receiver will respond in the following manner in order to indicate that the receiver is in the programming mode:
6.1. Locking the doors
6.2. Unlocking the doors
Important: All extra transmitters must be programmed at this time. When a new transmitter is programmed, it will deactivate the old transmitters.
Hold down the lock and unlock buttons on the transmitter until the remote control door lock receiver will respond in the following manner:
7.1. Locking the doors.
7.2. Unlocking the doors.
Repeat step 7 for each additional transmitter.
Turn the ignition switch to the ON position in order to exit the transmitter programming mode.

May 04, 2017 | 1998 GMC Jimmy

4 Answers

Passlock


turn key all the way on (not to start) let set for 1 hur cycle key and try it.

Jul 20, 2009 | 1999 GMC Jimmy

1 Answer

The remte control key is not responding with the car


Hi abdumi0f,

Firstly, open your glove box and make sure Valet Mode is not enabled, if it is not, follow these steps.

Step 1: Open drivers door and leave open.
Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.
Step 3: Insert key into the ignition.
Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.
Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).
Step 6: ECU should respond by locking and unlocking the doors.
Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.
Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.
Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

Hope this helps,

Lazaruselite

Feb 24, 2009 | 2007 Mercedes-Benz E320 BLUETEC Sedan

3 Answers

Program remote control for mazda mpv 2002


Courtesy of: forums.mazdaworld.org

Try this, it works on several 2002 models:


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the drivers door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the drivers door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done

Dec 06, 2008 | 2000 Mazda MPV

1 Answer

Programming keyless remote


2003-04 Mazda 6 REMOTE PROGRAMMING


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

Good Luck.

Jul 12, 2008 | 2003 Mazda Mazda6

2 Answers

Keyless entry remote


Try this, it works on several 2002 models:


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the drivers door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the drivers door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks.

Jun 20, 2008 | 2002 Mazda Protege

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...