Question about Jeep Cars & Trucks
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Fuse # 20, located in the Junction Block (interior, drivers side). This is a ten amp fuse.
Read the information at the above site. The TSB (technical service bulletin) may be of interest to you.
Posted on Nov 20, 2008
If you have the owner's manual look up fuses in the index, good illustration. If you don't, I do. It shows a relay and a 15 amp fuse. Look at the passenger kick panel, pull the cover, and it is #2 fuse (second from the top on the left) The see the relay you may have to pull the panel (two screws and a clip) the relay is the third cavity down, third row from the firewal side.
Let me know if this works for you?
Posted on Apr 03, 2009
The tail lights and the brake/turn lights use the same bulb but, there is 2 filamants in the bulb. One for tail lights and one for brake/turn lights. So just because the brake lights and turn signals work doesn't mean the bulbs are good. If bulbs are good you can check to see if there is power getting to the tail light assy's by unplugging the connector at the assy and using a test light probe the connector (harness side) with the headlights on. If you are getting power to the assy the test light will light. To make sure, turn off the headlights and test light will go off. Hope this is helpful. Good luck.
Posted on May 29, 2009
Definitely, you'll have to take a look to see if any obstruction is visible. To check the fuses first you'll need to find them. The fuse block cover should illustrate what each fuse is for. You can visibly check the fuses, with a flashlight. Just take a look at the sunroof fuse and check that its not burned. That the metal inside goes from one side to the other and its not burned or broken. You can use a test light or a multimeter, a test-light will do. I usually check them visibly, its obvious when you have a blown fuse just by looking at it. Its better just to pull out the suspected fuse to check it.
Posted on Jun 02, 2009
There are two parts to it, a voltage resistor, and the EL panel itself.
You need to remove the console first. There are 2 screws under the front rubber pad, two under the cup holder, two in the bin. Remove those six first, take the storage bin out, then slide the rear cupholder out, remove the two screws under the cup holder, and one in front of it.
There are a total of 6 flat screws, and 3 self tapping screws you have removed.
Put the parking brake on, shift the tranny to N, and the transfer case to the middle position if equipped.
Remove the entire console. Slide the shifter beezel as far up vertically as you can. There are 4 clips you ned to remove to do it.
You will see a blue and black wire running into the back. Follow those wires to the resistor. You will see a transparent EL panel attatched to the resistor by two clips.
Usually, one or both of these clips has come loose, causing the light to work intermittantly. Clip them back on, and turn on the headlights to confirm that the light works correctly now.
Re-install everything in the opposite order.
Posted on Oct 11, 2009
Tips for a great answer:
Oct 24, 2015 | 1999 Jeep Grand Cherokee
Feb 04, 2013 | 1999 Jeep Grand Cherokee
Aug 09, 2010 | 2004 Jeep Grand Cherokee
Jan 12, 2010 | 1994 Jeep Grand Cherokee
Nov 29, 2009 | 2001 Jeep Grand Cherokee
Sep 04, 2009 | 1999 Jeep Grand Cherokee
Jul 22, 2009 | 1994 Jeep Grand Cherokee
Jun 01, 2009 | 1999 Jeep Grand Cherokee
Jul 21, 2008 | 1999 Jeep Grand Cherokee
19 people viewed this question
Usually answered in minutes!