Question about Hyundai Sonata
No OBD codes. Have isolated evap canister from rest of system by removing 1/2" hose that goes to Neck (liquid-vapor separator), made no difference in gassing up. Also, checked Evap Canister manually, no charcoal pellets in any hoses, was able to blow air with little back pressure through canister, close valve and air filter. Suspect, fuel cut valve or vent valve. Not sure of other system components.
Top of fuel tank has fuel roll over valve or called vent valve. this is problem with hard to fill issue
Posted on Sep 12, 2019
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
CLICK on the following LINK. It has the Serpentine Belt Diagrams you will need.
If you would: Before Clicking let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Posted on Mar 02, 2010
SOURCE: fuel gauge / range meter
Actually I had that problem, its a faulty fuel sensor, and can be replaced under warranty. at first they had me unplug a fuse while the car was running then shut it off and plug it in then start the car. did that for 2 more fillups b4 they finally replace the faulty sensor.
Posted on Oct 26, 2008
These fuel tanks are designed weird, they have a hump in the middle for the driveshaft. Most of the time I have found if the pump clicks off early it is the fuel vent valve, which is located on the rh side, but a fuel cut valve could do the same thing. If the pump clicks off early (sometimes after 1 gal), make sure the canister filter isn't clogged and replaced the vent valve.
Posted on May 06, 2009
Tips for a great answer:
Feb 10, 2016 | Hyundai Cars & Trucks
Feb 08, 2015 | Hyundai Motor 2002 Sonata
Mar 28, 2013 | Cars & Trucks
Jun 11, 2011 | 2005 Hyundai Sonata
This TSB supersedes TSB 03-40-013 to add repair information (Steps 2~3).
An improperly adjusted or improperly operating range switch may result in the following conditions:
• Diagnostic trouble codes:
• P0705 - Range switch signal problem
• P0707 - Range switch - open circuit
• P0708 - Range switch - short circuit or multiple inputs
• Malfunction Indicator Light (MIL) illuminated
• Impossible engine start in "P" or "N"
This TSB provides information concerning the proper adjustment and diagnosis of the transaxle range switch.
1. Attach a GDS and check for DTC in both the "Engine" and "Automatic Transaxle" menus. Go to Step 2 for 2000~02 Accent or Step 3 for 2006~ Sonata. For other vehicles, go to Step 4.
2. For 2000~2002 Accent: Check according to TSB 03-40-001. Go to Step 4.
3. For 2006~ Sonata, follow steps a,b,c below, then go to Step 4.
a. Check the rear combination lamp ground bolts for tightness and good electrical contact (refer to applicable ETM, "Tail, Parking & License Lamps" section). Go to Step b.Page 2 of 6
b. For 2006~ Sonata: Remove the center console cover and check for contamination on the M40 connector to the sports mode switch. If so, clean and repair the connector as necessary. Go to step c below.
c. For 2006~07 Sonata: Remove the front pillar cover and verify the harness is properly routed near the clip. Repair the harness as necessary. Go to Step 4.
4. Attach a GDS and select vehicle, "A/T" menu, "Current Data" and "Shift Lever Switch".
5. Move the shift lever and confirm the GDS reads the gear shift position as shown below. If so, the harness currently does not have an open or short circuit between. the PCM/TCM and range switch.
Hope this helps.
Feb 11, 2011 | Hyundai Elantra Cars & Trucks
Apr 20, 2010 | 2006 Ford F-150
Dec 16, 2009 | Hyundai Motor 2002 Sonata
Jan 06, 2009 | 2000 Hyundai Sonata
22 people viewed this question
Usually answered in minutes!