Question about 2002 Ford Taurus

1 Answer

2002 ford taruas sputting when start up then put in gear go die out under a load

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 1,580 Answers

Clean out the throttle body with fuel injection cleaner then check your vacuum lines if all are good then you should have codes set your check engine light should be on verify that the check engine light bulb is not burned out turn the key to the on position you should see all the dash lights //oil//battery//check engine light if you don't see it the bulb is blown out and if all other things I mentioned are done and the problem is still there either your throttle position sensor is bad or your idle air control valve but I would go to the throttle position sensor first because your car is now 17-18 years old by the door sticker date and if you don't know the repair history because it's a used car check that sensor first if you can get a code scanner from someone/ loaner from autozone you will no for sure

Posted on Sep 15, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 467 Answers

SOURCE: 2002 ford taruas 3.0Lv6 keep having 2 replace coil

check your vacuum line and the electrical systems

Posted on Jul 16, 2009

  • 7353 Answers

SOURCE: i have a 2002 ford excursion 4x4 v10 it starts but

ck trans fluid level. if its low, it could cause this. or the IAC (idle air control) valve is faulty.

Posted on Oct 14, 2009

  • 14092 Answers

SOURCE: My 2002 ford taurus ses starts and shift gears but

HAVE CAR SCANNED TO CHECK FOR TRANSMISSION FAULT CODES.

Posted on Feb 01, 2010

  • 1206 Answers

SOURCE: 2002 ford taruas idles at 800 rpm in drive and

you have a bad temp sender,if this does not solve the rough idle than you have multiple issues and your idle control valve is not functioning properly try removing and cleaning it.its also referred to as IAC (intake air control)

Posted on Feb 05, 2010

play0027
  • 107 Answers

SOURCE: belt diagram on 2002 ford

Dayco.com offers a free online comprehensive serpentine belt reference tool - including routing diagrams and tensioner information.

Somewhere under the hood, usually on the fan shroud or near the radiator, there should be a sticker with a diagram of the belt routing, 2001 may even be on the hood. On this diagram it will show a tensioner pulley and idler pulley and the approximate location. Most Fords use a 15mm or 16mm bolt on the tensioner, this is where you put a wrench to rotate the tensioner and remove the belt. When you turn the tensioner bolt turn towards the front of the car, there will be a lot of tension so pull hard.

Posted on Nov 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 mustang start and run fine in p or n,put it in gear dies unless i rev it up and put it in gear.once i'm moving, it up shift fast and is sluggish until i get speed,does fine until i have to stop


What engine does yours have ? 3.8 or 4.6 Do you have a professional type scanner that will show sensor data parameters ? Is the check engine light on ,or anyother light's ? Wrench symbol .
012 Idle Speed Problems Idle Speed Wrong I know yours only dies when put into gear , idles fine in park an neutral . Just showing what scan data is , if your not familiar with it. With the problem your having it's a necessity to have a scan tool that can view data pid's . You could spend a lot of buck's just replacing part's on recommendations from people on here . Testing an not guessing is the way to find the problem .

May 22, 2018 | 2002 Ford Mustang

2 Answers

2002 ford explorer engine will stop running as soon as you put it in gear \


Could be a lot of thing's , you should have it checked at a qualified repair shop .

Nov 19, 2016 | Ford Cars & Trucks

1 Answer

I have a 2002 Ford Ranger it's cuts off when stoping hard and then I have trouble getting to stay running after starting back up and putting it in drive


My work truck run great until you put it in gear it would die it jerked hard in reverse like it was missing . And it was the shift telay

Apr 05, 2015 | 2002 Ford Ranger

1 Answer

What could issue be when caliber starts fine but dies when put in gear?


it is obvious that under a load the car will not run
first do a tune up and make sure all cylinders are firing,check codes and even do a fuel pressure check

Aug 30, 2014 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

Location of o2sensors 2002 taruas duratec 24 valve where?


Check the exhaust manifold just above where the exhaust pipe connects to the manifold. The second location, is you have two, is under the drivers side on the exhaust pipe just past the Catalytic Converter.

Oct 25, 2011 | 2002 Ford Taurus

1 Answer

My 2002 Ford Taurus, just recently started to not start back up after being turned off. At first thought was battery and/or alternator but all checked working fine. Car died again, thought was battery...


could be bad water pump,leaking anti freeze,may have blown the head gasket as result overhaeting engine,check oil for milky gray color,or see if coming out exhaust if so blown head gasket,have someone help you check it out

Aug 21, 2011 | 2002 Ford Taurus

1 Answer

Belt diagram on 2002 ford taruas 3.0


Dayco.com offers a free online comprehensive serpentine belt reference tool - including routing diagrams and tensioner information.

Somewhere under the hood, usually on the fan shroud or near the radiator, there should be a sticker with a diagram of the belt routing, 2001 may even be on the hood. On this diagram it will show a tensioner pulley and idler pulley and the approximate location. Most Fords use a 15mm or 16mm bolt on the tensioner, this is where you put a wrench to rotate the tensioner and remove the belt. When you turn the tensioner bolt turn towards the front of the car, there will be a lot of tension so pull hard.

Nov 20, 2010 | Ford Taurus Cars & Trucks

1 Answer

2002 ford taruas idles at 800 rpm in drive and


you have a bad temp sender,if this does not solve the rough idle than you have multiple issues and your idle control valve is not functioning properly try removing and cleaning it.its also referred to as IAC (intake air control)

Feb 05, 2010 | 2002 Ford Taurus

1 Answer

I have a 2002 ford excursion 4x4 v10 it starts but when you put in gear it dies what could it be.


ck trans fluid level. if its low, it could cause this. or the IAC (idle air control) valve is faulty.

Oct 14, 2009 | 2002 Ford Excursion

Not finding what you are looking for?
2002 Ford Taurus Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...