Question about Mercury Cars & Trucks

Open Question

Program remote 2005 mercury grand marquis. I am locked out of car, and remote has new battery and needs programming...or how do mi break in? lol

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: program remote keyless entry

1) Turn key from OFF to ON eight times within 10 seconds ending in the ON position.

2) After doors lock then unlock, press any button on the
remote being programmed.

3) The doors should lock/unlock to confirm programming.

4) Turn key to OFF and door locks should cycle one last time.

Posted on Aug 17, 2008

Ad
  • 82 Answers

SOURCE: Car will not unlock.

To get inside the car .... Use the key in the lock cylinder, unlock the drivers door to get inside. You shouldn't have to reprogram the fob unless it or the keyless module was changed. There may be a blown fuse that supplies the keyless control module (check the owners manual for location). or wires that lead into the Drivers door may be damaged ... The keyless module is located inside the drivers door at the bottom behind the door panel ... do the unlock/lock and trunk release switches on the inside of the drivers door operate the locks and or trunk release? If so it is not the fuse ... and not the wires to it ... And it could be your BCM body control module, located in the dash board to right of your gas petal. Because the number entry keypad (code for that is on the inside of the right passenger trunk bracket arm) also doesn't work I assume it's not the key fobs themselves. Your 98 manual is correct for your car.

Posted on May 04, 2009

rockitman187
  • 2559 Answers

SOURCE: My key fob remote will not unlock car doors but will start car

Here you go.If you can't read it I can email it to you.
c2293a3.jpg

Posted on Aug 04, 2009

  • 144 Answers

SOURCE: I have a 2005 Mercury Grand Marquis and I can't turn the wipers.

this is a very common problem on these vehicles. the wiper motor has a park switch built into it that fails. replace the wiper motor and this will stop problem. hope this info helps you!

Posted on Sep 22, 2009

  • 564 Answers

SOURCE: how to replace starter +1993 Mercury Grand Marquis

disconnect battery,,jack car up,,put jack stand on frame,,take starter bolts out,(may not be easy),,take wires off starter,,hoped it helped,,

Posted on May 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remote on key fob wont unlock doors on 2001 merc marquis


Tested the batteries in it? Is it a new one? One that did not come with car? If so, it has to be programed so the car recognizes it, location for that is behind the glove box.

Mar 09, 2013 | 2000 Mercury Grand Marquis

1 Answer

Got a 2003 mercury grand marquis which i bought and didnt come with a remote for the door locks. i have an extra remote from my 2003 ford expedition and need to know how to program it, any suggestions?


usually the truck and car fobs work on different signals. you can get inexpensive fobs on ebay, the car fob will have four buttons with a trunk release button.
once you have the correct fob, its pretty easy.
  • Just remember that you must also re-program your currently working remotes at this time also as if they are new since prior remotes are erased.
  • Max of 4 transmitters can be programmed.
Procedure:
  • Keep the driver's door open.
  • Electronically unlock the doors (Switch on door or working transmitter)
  • 2000-2006: Turn the ignition from OFF to RUN/ON 8 times within 10 seconds, with the eighth turn ending in RUN. If the module has successfully entered program mode, it will lock and then unlock all doors.
  • Within 20 seconds, press any button on an transmitter, and the doors will lock and then unlock to confirm that each transmitter has been programmed. Repeat this step for each transmitter.
  • NOTE: If the door locks do not respond for any transmitter, wait several seconds and press the button again.
  • To exit the programming mode:
    • Turn ignition to the OFF position.
    • Let the 20 seconds expire.
    • The maximum number of transmitters have been programmed.

Sep 04, 2010 | 2003 Mercury Grand Marquis

1 Answer

My door lock remote will not function and new


have you tried to press/hold lock button for 30 secs.
the code changes everytime you use the remote so that only your remote unlocks your car,not everybody elses.the key has a code inbuilt into it so the car will only start with your key...(this is dealer programmable)

Apr 05, 2010 | 2000 Mercury Grand Marquis

1 Answer

How to change the keypad code on a 2001 mercury grand marquis


look for the permanent code on the plastic card in the owner manual packet. Or, pay dealer to extract code from computer.

Keyless Entry Keypad Code Programming NOTE: The system only allows one code to be programmed.
  1. Enter the permanent factory keyless entry keypad code.
  1. Press the 1/2 button within five seconds to activate the programming mode. Holding the 1/2 button for more than two seconds after activation will erase the stored customer code . The door locks will lock, then unlock, confirming the code is erased. The existing code will not need to be erased to program new a code.
  1. Within five seconds, enter the new five-digit keyless entry keypad code. The door locks will lock and unlock to confirm the new code is programmed.

Feb 08, 2010 | 2001 Mercury Grand Marquis

1 Answer

Power locks, and keyless entry pad do not work. all fuses are good. 92 mercury grand marquis


if the battery in the entry pad is good then it needs to be reprogramed or the remote sensor is blowen

Jul 08, 2009 | 1992 Mercury Grand Marquis

1 Answer

I need to program the key fob


. Enter 5-digit permanent entry code into the keyless entry driver door keypad. 2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors will lock then
unlock confirming you are in programming mode.

3. Press any button on first Keyless Remote within 5 seconds of pressing the 1/2 button. Locks will
cycle to indicate succesful programming.

4. If you are programming more than one Keyless Remote (Including any exsiting remotes) Press
any button on second keyless remote within 5 seconds of previous remote. Locks will cycle again
to indicate succesfull programming. (If the keypad light goes out before all remotes are
programmed the entire process must be repeated).

5. Press the 7/8 and the 9/0 buttons simultaneously on the keypad to exit program mode.

Jun 29, 2009 | 1997 Mercury Grand Marquis

1 Answer

1999 Grand Marquis remote control - no buttons work


10 year old remotes go bad often, especially due to moisture retention.

Nov 28, 2008 | 1999 Mercury Grand Marquis

1 Answer

Fob programming


Owners manual should explain

Aug 11, 2008 | 1995 Mercury Grand Marquis

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4388 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

fordexpert

Level 3 Expert

5692 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...