Question about 2006 Jeep Grand Cherokee

Open Question

2006 jeep grand Cherokee headlamp assembly removal( passenger side): got the grill off and the air filter intake removed as well as one of the 3 screws holding the assembly in. However i cant figure out how to get to the 2 screws below the assembly that are blocked by the bumper. It seems that the bumper would have to be removed to get to these 2 screws. Any input would be greatly appreciated!

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 85206 Answers

SOURCE: jeep over heating

The cooling fan relays are located there, check the sockets they are plugged into for damage.

Posted on Oct 31, 2008

Ad
  • 90 Answers

SOURCE: HOW TO REMOVE HEADLIGHT ASSEMBLY 2006 JEEP GRAND CHEROKEE

remove the 7mm bolt in the centre top of lamp unit then with a big screwdriver just behind headlamp prise outwards quite firmly

Posted on Jul 03, 2009

  • 295 Answers

SOURCE: need to get the headlamp assembly off a 2006 jeep grand cherokee

1. Disconnect and isolate the battery negative cable. 2. Remove the cover from over the top of the front lamp unit (1). (Refer to 08 - Electrical/8L - Lamps and Lighting/Lamps/Lighting - Exterior/UNIT, Front Lamp - Removal) . 3. Remove the grille from the front of the vehicle. (Refer to 23 - Body/Exterior/GRILLE - Removal) . 4. If the front lamp being serviced is on the same side of the vehicle as the engine fresh air intake tube, unsnap the air intake tube from the air cleaner housing and remove it from between the lamp and the radiator yoke hydroform. 5. Remove the three screws (3) that secure the two lower and the upper inboard lamp mounting brackets to the front end sheet metal. 6. If equipped, remove the push pin fastener (2) that secures the upper outboard lamp mounting bracket to the top of the radiator yoke hydroform. 7. The lower inboard lamp mounting bracket is captured between a metal mounting bracket on the top of the front frame crossmember and a tab of the plastic front fascia reinforcement. Push the tab of the front fascia reinforcement forward far enough for lamp mounting bracket clearance while maneuvering the lamp unit inboard during removal. 8. Pull the lamp away from the front of the vehicle far enough to access and disconnect the headlamp and dash wire harness connector (5) from the pigtail connector on the back of the lamp housing. 9. Remove the lamp unit from the vehicle.

Posted on Jul 25, 2009

ZJLimited
  • 17970 Answers

SOURCE: How do you remove the headlamp assembly on a 95

Review the ZJ Repair Manual Secc-8L-Lamps (page 5)

Is an easy work; remember rated this help. Good luck.

Posted on Nov 28, 2009

michigan man
  • 3533 Answers

SOURCE: instruction foreplacing headlamp assembly 2001jeep grand cherokee

give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local Jeep dealership in the parts department and they be able to print you off the pictures and diagrams you will need wish you the best of luck Michigan Man.

Posted on Jan 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the radiator relay switch in 2001 jeep cherokee grand laredo


under the passenger head light.....you have to remove the grill and remove the passenger side of the front nose cover....pain in the ****.....simple way...remove passenger headlight and cut a 3 inch circle out of the plastic....center of where the bottom of the headlight sits.....and the relay is mounted to the inner fender ....a dremel tool works perfect.....

Sep 18, 2011 | 2001 Jeep Grand Cherokee

1 Answer

Hi, i have a 2001 grand jeep cherokee 6 cylinder larado, the car is not running hot, the fan won't stop running, i was told to disconnect the battery cable which i did so do i need a new fan?


you probably have a bad solid state fan relay. This is a very common problem with jeeps. You'll love where they put this one. It is located under the passenger side headlamp assembly, but wait it gets better. The entire front headlamp grill support needs to be removed in order to gain access to the relay. The good thing is there is a shortcut that involves cutting a small hole in the headlamp/grill support under the passenger side headlamp assembly. I have a photo that shows where to make the hole and can post it if your interested in trying to tackle this yourself.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Sep 08, 2011 | 2001 Jeep Grand Cherokee

1 Answer

Where is the cabin air filter in 2001 jeep cherokee


It is under the passenger side cowl grill. Remove the passenger side windshield wiper, remove the cowl, remove filter and housing. Install new filter and housing in reverse order.

Mar 20, 2011 | 2001 Jeep Grand Cherokee

1 Answer

2006 jeep grand cherokee front headlight removal blue print


  1. Disconnect and isolate the battery negative cable.
  2. Remove the cover from over the top of the front lamp unit
  3. Remove the grille from the front of the vehicle.
  4. If the front lamp being serviced is on the same side of the vehicle as the engine fresh air intake tube, unsnap the air intake tube from the air cleaner housing and remove it from between the lamp and the radiator yoke.
  5. Remove the three screws (3) that secure the two lower and the upper inboard lamp mounting brackets to the front end sheet metal.
  6. If equipped, remove the push pin fastener (2) that secures the upper outboard lamp mounting bracket to the top of the radiator yoke
  7. The lower inboard lamp mounting bracket is captured between a metal mounting bracket on the top of the front frame cross-member and a tab of the plastic front fascia reinforcement. Push the tab of the front fascia reinforcement forward far enough for lamp mounting bracket clearance while maneuvering the lamp unit inboard during removal.
  8. Pull the lamp away from the front of the vehicle far enough to access and disconnect the headlamp and dash wire harness connector (5) from the pigtail connector on the back of the lamp housing.
  9. Remove the lamp unit from the vehicle.
  10. 56fe516.gif

Oct 16, 2010 | 2006 Jeep Grand Cherokee

1 Answer

1999 Jeep Grand Cherokee 4.0L 6cyl: Radiator fan is CONTANTLY running, even with the engine and everything turned off - it has drained my battery. Have no idea what could be keeping the fan running, please...


there is a solid state fan relay located under the passenger side headlight assembly. There are two ways to get at it. Either you can tear apart the entire front of the vehicle or you can remove the passenger side headlamp assembly and carefully drill a hole about in the middle of the opening and down towards the ground. Look in the hole you drilled you should be able to see the relay. Continue drilling/cutting until you have a hole just large enough to get the old relay out and a new one in. The hole will be covered by the headlamp and has become the preferred method of replacing since they are so common and removing the entire front assembly is so time consuming.

http://img.photobucket.com/albums/v493/twister55/jeep/DSC02093.jpg

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Sep 26, 2010 | 1999 Jeep Grand Cherokee

1 Answer

HOW TO INSTALL CHROME GRILL FOR JEEP GRAND


Review this info... Grille removal and installation 2005-2009

1. Remove the 6 plastic push pins. The pins are comprised of two pieces. With a small flat screwdriver pry up the circular pin top and remove. Then pry up and remove the sleeve.
2. Tip grille forward and remove. Be careful not to scratch top of fascia.
3. When replacing the grille, be sure that the tabs along the bottom are aligned correctly over the lip of the fascia.

Image 1: http://www.wkjeeps.com/grilles/2005_wk_grille_01.jpg
Image 2: http://www.wkjeeps.com/grilles/2006_wk_grille_rem_01.jpg

Good luck!!

Jul 21, 2009 | 2006 Jeep Grand Cherokee

1 Answer

Need to get the headlamp assembly off a 2006 jeep grand cherokee how do I get it off?


1. Disconnect and isolate the battery negative cable. 2. Remove the cover from over the top of the front lamp unit (1). (Refer to 08 - Electrical/8L - Lamps and Lighting/Lamps/Lighting - Exterior/UNIT, Front Lamp - Removal) . 3. Remove the grille from the front of the vehicle. (Refer to 23 - Body/Exterior/GRILLE - Removal) . 4. If the front lamp being serviced is on the same side of the vehicle as the engine fresh air intake tube, unsnap the air intake tube from the air cleaner housing and remove it from between the lamp and the radiator yoke hydroform. 5. Remove the three screws (3) that secure the two lower and the upper inboard lamp mounting brackets to the front end sheet metal. 6. If equipped, remove the push pin fastener (2) that secures the upper outboard lamp mounting bracket to the top of the radiator yoke hydroform. 7. The lower inboard lamp mounting bracket is captured between a metal mounting bracket on the top of the front frame crossmember and a tab of the plastic front fascia reinforcement. Push the tab of the front fascia reinforcement forward far enough for lamp mounting bracket clearance while maneuvering the lamp unit inboard during removal. 8. Pull the lamp away from the front of the vehicle far enough to access and disconnect the headlamp and dash wire harness connector (5) from the pigtail connector on the back of the lamp housing. 9. Remove the lamp unit from the vehicle.

Jul 17, 2009 | 2006 Jeep Grand Cherokee

2 Answers

HOW TO REMOVE HEADLIGHT ASSEMBLY 2006 JEEP GRAND CHEROKEE


remove the 7mm bolt in the centre top of lamp unit then with a big screwdriver just behind headlamp prise outwards quite firmly

May 20, 2009 | 2006 Jeep Grand Cherokee

2 Answers

Cant find the fan relay for 2002 jeep cherokee


It lives under the right headlamp assembly. You can remove the front fascia and headlamp bracket to gain access, or you can just remove the right headlamp and use a hole saw to drill a hole in the bracket assembly. It is made of a hard plastic material and the relay is bolted to the fender area underneath.

Apr 27, 2009 | 2000 Jeep Grand Cherokee

1 Answer

How do you take old headlight assembley out of a 1999 jeep grand cherokee


tious of the sha Open the hood, and using a 7mm socket remove the long headlamp jackscrew, 2nd from left. Grasp the headlight assembly on the upper inboard and lower outboard corners and wiggle and pull very firmly outward to disengage the 3 ball stud alignment posts from their sockets (be cautious of the sharp edges of the grille and fender areas surrounding the headlamp).
rp edges of the grille and fender areas surrounding the headlamp).

Feb 25, 2009 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
2006 Jeep Grand Cherokee Logo

Related Topics:

412 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...