20 Most Recent 1984 Honda GL 1200 Interstate Gold Wing Questions & Answers


Hi, Amos for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?sa=X&q=Fuel+line+routing+1984+Honda+GL1200+Interstate+Goldwing&tbm=isch&source=univ&ved=2ahUKEwjd3pCa5bDjAhXQmVkKHVg5CGoQsAR6BAgGEAE&biw=1440&bih=757
https://goldwingdocs.com/forum/viewtopic.php?t=9803
https://www.manualslib.com/manual/1443589/Honda-1986-Goldwing-Gl1200a.html
https://www.partsfish.com/page/oem-parts-for-honda
Honda GL1200 1986 Owner Manual

1984 Honda GL... | Answered on Jul 13, 2019


Hi, Scott before diagnosing your blown fuse issue, check the bottom of your seat, if its metal and comes in close proximity to the positive battery post you need to take the necessary steps to ensure there is no contact (electrical tape, thick rubber insulation, hammer a dent in the seat bottom etc.) You are going to need a wiring diagram from your service manual, a test light, an ohmmeter and plenty of extra fuses.
If you turn on your ignition switch and immediately blow a fuse you have a hard/dead short and is usually easy to find. With a test light connected to the hot side of the blown fuse holder start stabbing the wire/s that leads away from the fuse holder and towards the ignition switch, you test light will illuminate validating the short. When the test light fails to illuminate you have passed the short and need to back up until the test light illuminates, then look in the immediate area for the short.
If you driving down the road for 30 minutes or 15 miles and blow a fuse you have soft/flying short and may take some time and patience to find.
If the main fuse/circuit breaker constantly blows/trips while riding you probably have a faulty battery terminal connection. Check battery terminals for damage or corrosion, check battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary. Any other fuses that constantly keep blowing while riding are usually caused by a loose or corroded ground wire in the circuit, which means you have to check, inspect, test each and everyone with an ohm meter set on a low ohm scale 100 ohms or less . Simply touch one lead to the ground source and the other lead to the battery negative terminal, a reading of zero indicates a clean solid ground. Any reading or infinity indicates a poor ground and needs to be repaired. Poor or weak grounds require excessive additional amperage to complete the circuit which in turn blows the small amperage fuse.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
84 1200 Blowing 30A main fuse Steve Saunders Goldwing Forums
https://goldwingdocs.com/forum/viewtopic.php?t=28187
Honda GL1200 Owners Workshop Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda GL1200 Aspencade Owner Manual

1984 Honda GL... | Answered on Jul 17, 2018


Hi, P_listro for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://goldwingdocs.com/forum/viewtopic.php?t=17995
1984 Honda GL1200 Interstate Goldwing air cutoff valve location Google...
Honda GL1200D Shop Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda GL1200 1986 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1984 Honda GL... | Answered on Feb 20, 2018


Hi, Revesstil and the usual suspects are:
1. Low coolant level.
2. Restricted radiator air flow.
3. Faulty thermostat.
4. Coolant pump or fans inoperative.
5. Vent hose crimped.
6. Air in the coolant and needs bleeding.
7. Engine idling too long or bike moving too slow.
8. Coolant too old needs to be replaced.
9. Faulty temperature sensor, wiring or connector.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Overheating 1984 Interstate
overheating GL1200 Information Questions goldwingdocs com Honda GL1200D Shop Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda GL1200 1986 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1984 Honda GL... | Answered on Feb 15, 2018


Hi, Biscuitmaker for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
1984 Honda GL 1200 Interstate Gold Wing vin number location Google Search
VIN Number Location Tech Talk goldwingdocs com
Honda GL1200D Shop Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda GL1200 Aspencade 1985 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1984 Honda GL... | Answered on Jan 23, 2018


Hi, Juliekrausz for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
1984 Honda GL 1200 Interstate Gold Wing air compressor location Google...
How do you use the GL1200 air hose
Honda GL1200D Shop Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda GL1200 1986 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1984 Honda GL... | Answered on Jan 18, 2018


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Torquesetting head bolts GL1200 Information Questions goldwingdocs com
GL1200 cylinder head bolts torque pattern
Honda GL1200D Shop Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda GL1200 Aspencade 1985 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1984 Honda GL... | Answered on Dec 17, 2017


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Honda Motorcycle Wiring Diagrams
1984 Honda GL1200 Interstate Goldwing wiring diagram Google Search
Honda GL1200 Aspencade Owner Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda GL1200D Shop Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1984 Honda GL... | Answered on Nov 22, 2017


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
GL1200 Pulse Generators
GL1200 Stator Replacement
Honda GL1200D Shop Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda GL1200 1986 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


1984 Honda GL... | Answered on Nov 13, 2017


Hi, Bill if your bike has been sitting idle for months or years and you did not do any pre-storage maintenance I feel your pain it will probably have a dead battery and not want to start or if it starts it will not idle unless the choke is full on and run poorly then stall, here are the following steps necessary to complete in order to get your bike back to an acceptable running condition and in the future pour in a bottle of fuel stabilizer and injector cleaner for you FI folks at least 2 times a year and before storage.
1. If your battery was 2-3 years old when you last had the bike running you should replace it.
2. If you believe your battery might still be serviceable remove it from the bike and put it on a 1 or 2 amp trickle charger for 24 hours. If it is the old lead acid type with visible cells and acid levels fill each cell to the top line with distilled water and replace the caps, run the vent tube into a plastic or styrofoam cup, any cells that are cloudy/milky replace the battery.
3. After charging the battery remove the leads and let it sit for a couple of hours then check the battery voltage with a voltmeter, you should have 12.5 volts or more, any readings in the 11 volt range you need to do a proper "LOAD" test on the battery and replace as necessary, you may have 12.5 volts or better but little or zero amps, any readings in the 10 volt range you have a dead cell and the battery needs to be replaced.
4. Drain and flush fuel tank if it rusty there is a cheap and easy fix. https://www.youtube.com/watch?v=fUYr_7SwGms
5. Remove and inspect your air cleaner paper elements that are not oil soaked can be cleaned with a soft brush and low pressure compressed air, oil-soaked elements must be replaced. Gause mesh and foam elements can be cleaned by soaking them in a container big enough to completely cover them with a solution of 1 gallon of water and 1 oz. of Dawn dishwashing liquid for small and medium size elements, for monster size double the formula and let soak for at least one hour then rinse with warm water shake off excess and let air dry, "WARNING" do not use compressed air as this will embed micro-sized dirt and road grime and destroy the mesh pattern and stretch foam elements out of shape just squeeze it like a sponge and let air dry, use a fan if you're in a hurry. When completely dry spray a very fine mist of air filter oil evenly around the whole element.
6. Remove the carburetors, disassemble and decontaminate with a "CARB DIP" or if you have EFI remove injectors and clean with carb spray and compressed air
7. Check intake manifold and seals for leaks and craks.
8. Remove fuel valve and filter disassemble and clean as necessary, remove, clean, and inspect fuel and vacuum lines and replace as necessary.
9. Replace spark plugs with new ones and check for spark.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Motorcycle Views
How To Get Stored Motorcycle Running Motorcycle Repair
Honda GL1200 Owners Workshop Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda GL1200 Aspencade 1985 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e



1984 Honda GL... | Answered on Nov 06, 2017


Hi, Anonymous the starter clutch is a separate mechanical gear driven component that is activated by the starter motor, it engages the clutch pack gear or the flywheel gear to turn over the engine. It has an internal mechanism that allows the gear to turn in one "ONE DIRECTION" only and once the engine starts allows the gear to free spin with engine rotation. If the starter gear free spins in "BOTH DIRECTIONS" then the drive gear has failed, it might be serviceable on some models but usually needs to be replaced.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Starter clutch not engaging 84 Aspencade GL1200 Information Questions...
Honda GL1000 Starter Clutch Repair Details by Randakk
Honda GL1200 Owners Workshop Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda GL1200 1986 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


1984 Honda GL... | Answered on Oct 24, 2017


Hi, Anonymous for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
1984 Honda GL 1200 Interstate Gold Wing radiator cap location Google Search
check the antifreeze in 1985 goldwing GL1200 Information Questions...
Honda GL1200 Owners Workshop Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda GL1200 1986 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1984 Honda GL... | Answered on Oct 23, 2017


Hi, Anonymous not unless it was underwater, before testing any electrical component in the Starting System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand, clutch, neutral safety switch.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter have failed or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. Faulty ignition relay.
14. The electric starter is working but starter clutch has failed.
15. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
GL1200 it will not start
85 Goldwing 1200 won start GL1200 Information Questions goldwingdocs com
Honda GL1200 Owners Workshop Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda GL1200 1986 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1984 Honda GL... | Answered on Jul 28, 2017


Hi, Dale for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
think my ignition control unit is bad Motorcycle Technical Questions...
1985 ECU GL1200 Information Questions goldwingdocs com
Honda GL1200 Owners Workshop Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda GL1200 1986 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1984 Honda GL... | Answered on Jul 09, 2017


Hi, Arthurcampaz for this scenario you will need your service/owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
How to bleed clutch GL1200 Information Questions goldwingdocs com
Goldwing Clutch Bleeding Tip
Honda GL1200D Shop Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda GL1200 1986 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


1984 Honda GL... | Answered on Jun 30, 2017


You don't fix it you replace it. Just take it off the front axle and pull the cable out.

1984 Honda GL... | Answered on Feb 20, 2015


There is only two wires and they can't be reversed. One is fat and comes from the battery the other is thin and comes from the starter switch. power to the thin wire excites the solenoid and the motor turns.

1984 Honda GL... | Answered on Jul 14, 2014


Check Aerial connection for corrison also check resistance ,check the radio is grounded and That there's a surge protected best of luck

1984 Honda GL... | Answered on Apr 23, 2014


It may be a problem with your pipe being clogged or dented badly. In a worse case, it could be that the cylinder is not firing. If you can, start your bike, and feel the pipe right at the header to see if it is getting hot. If the pipe stays cool while the others are hot, your cylinder is not firing. If that is, check the spark plug to see if it is fouled or cracked. If the plug is good, check if the cylinder is getting fuel because it could be that your carb is clogged.

1984 Honda GL... | Answered on Mar 11, 2013

Not finding what you are looking for?
1984 Honda GL 1200 Interstate Gold Wing Logo

Popular Tags

35 questions posted

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5914 Answers

Marvin
Marvin

Level 3 Expert

85108 Answers

richard libby

Level 2 Expert

208 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GL 1200 Interstate Gold Wing Honda

  • GL 1200 Interstate Gold Wing Honda

Most Popular Question

one exhaust pipes working great other

  • Motorcycles
Loading...