20 Most Recent 2002 Suzuki GZ 125 Marauder - Page 6 Questions & Answers


Hi, Lfd322 for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://advrider.com/f/threads/suzuki-mt50-trail-hopper-what-oil-to-use.474981
https://www.google.com/search?q=Oil+type+1972+Suzuki+MT50+Trailhopper&tbm=isch&source=univ&sa=X&ved=2ahUKEwiukf7hlJviAhURRKwKHTfNDgcQsAR6BAgJEAE&biw=1440&bih=757
http://wpa.mofga.org/suzuki_mt50_manual.pdf
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Suzuki... | Answered on May 14, 2019


Hi, Anonymous before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.doityourself.com/forum/motorcycles-snowmobiles-go-carts-motorized-bikes-atvs-electric-mobility-scooters-golf-carts/231365-suzuki-gs1000-wont-start.html
https://www.ar15.com/forums/general/interesting_problem_on_an_old_bike___suzuki_gs1000__1978_/134-1476291
Suzuki GS1000 Service Manual
https://www.partsfish.com/oem-parts-for-suzuki
http://gsarchive.bwringer.com/mtsac/~cliff/storage/gs/GS1000G_Owners_Manual_80.pdf

Suzuki... | Answered on May 14, 2019


Hi, Anonymous before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://burgmanusa.com/forums/14-burgman-400-1999-2006-model-years/48429-won-t-start-engine-will-not-turn.html
What To Do If Your Motorcycle Doesn Start
https://www.croooober.com/en/item/3878013/Other-Accessories/SUZUKI-Skywave-250-Service-Manual
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Suzuki... | Answered on May 14, 2019


Hi, Jesseok580 before testing any electrical component in the Turn Signal Light Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test because your battery may have 12.5 volts or more but little or zero amps causing the battery to be faulty and must be replaced, "AGM" batteries fall into this category more so than lead-acid types, also before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced your OEM lights with one or all LED lights you are going to need a load equalizer.
If no turn signals are working the cause could be a faulty turn signal module/flasher or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion.
If your turn signal comes on but takes several seconds before it starts flashing you may have dirty contacts in the turn signal switch/button, the switch needs to be opened up and cleaned also the flasher may be starting to fail. It should be noted that cold weather will only exacerbate the situation especially when temperatures drop down below freezing and the location of the component, turn signal switches on the handlebar are at the mercy of the oncoming freezing 70 mph wind and makes it hard for the contacts to do their job covered in frozen grease/grime
If all four turn signals flash at the same time like hazard lights even though you only pressed one turn signal button then you have a LED light in the circuit and need a load equalizer that can be purchased from any motorcycle parts supplier.
If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function.
If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction.
If your rear turn signals don't work check your rear fender wiring harness connector first, look for, corroded, broken, loose pins/sockets, power, and a good ground, the harness connector is usually located under the seat on the front of the rear fender then keep tracing the wiring look for obvious harness damage caused by the rear tire.
If you still can't find the malfunction backtrack from the rear fender wiring harness connector.
If one side does not work you could have a faulty turn signal switch or module check for continuity.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Left+turn+signal+not+working+1978+Suzuki+GS1000&tbm=isch&source=univ&sa=X&ved=2ahUKEwju0ITh6JriAhXBnOAKHRysD0EQsAR6BAgJEAE&biw=1440&bih=757
Troubleshoot Repair motorcleTurn signal light
Suzuki GS1000 Service Manual
https://www.partsfish.com/oem-parts-for-suzuki
http://gsarchive.bwringer.com/mtsac/~cliff/storage/gs/GS1000E_Owners_Manual_79.pdf

Suzuki... | Answered on May 14, 2019


Hi, Scott for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Wiring+diagram+1984+Suzuki+RM80&tbm=isch&source=univ&sa=X&ved=2ahUKEwiD-8DnyJriAhVNTd8KHT3TAbMQsAR6BAgJEAE&biw=1440&bih=757
Suzuki Motorcycle Wiring Diagrams
Suzuki RM85 Owner Service Manual
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Suzuki... | Answered on May 14, 2019


Hi, Autowise for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere $19 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.youtube.com/watch?v=3PbybnbB-So
How to adjust Valce Clearance 1985 Suzuki GS400
https://www.tradebit.com/filedetail.php/280105158-suzuki-gs250-gsx250-gsx400-gsx450-twins-motorcycle $19
https://www.partsfish.com/oem-parts-for-suzuki
http://gsarchive.bwringer.com/mtsac/~cliff/storage/gs/GS450GA_Owners_Manual.pdf

Suzuki... | Answered on May 14, 2019


Hi, Claudioecara for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
How To Do Full Motorcycle Cluch Adjustment
re adjusting the clutch on the suzuki
http://wpa.mofga.org/suzuki_shogun_fd_110_service_manual.pdf
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Suzuki... | Answered on May 14, 2019


Hi, Ian_morfitt for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.bwringer.com/gs/tachcableseals.html
Changing your tach drive cable
Suzuki GS850G Service Manual
https://www.partsfish.com/oem-parts-for-suzuki
http://gsarchive.bwringer.com/mtsac/~cliff/storage/gs/1982_GS850G_Owners_Manual.pdf

Suzuki... | Answered on May 14, 2019


Hi, Cherybomb901 for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Timing+specs+1982+Suzuki+GS300L&tbm=isch&source=univ&sa=X&ved=2ahUKEwjnhInGspriAhWonuAKHaibA0EQsAR6BAgIEAE&biw=1440&bih=757
http://www.ricepaddy.com/suzuki-gs300l-timing-pickups-pulser-coils-82-85.html
https://www.youtube.com/watch?v=3PbybnbB-So
https://www.tradebit.com/filedetail.php/278465506-1981-1983-suzuki-gs250t-gs300l-motorcycel-service-repair $15
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Suzuki... | Answered on May 14, 2019


Hi, Frankp845 for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Wiring+diagram+1986+Suzuki+GS+450&tbm=isch&source=univ&sa=X&ved=2ahUKEwj345e1r5riAhXvRd8KHdfZAYQQsAR6BAgJEAE&biw=1440&bih=757
https://onedrive.live.com/?cid=2370B62DDF9F0C6B&id=2370B62DDF9F0C6B%211031&parId=2370B62DDF9F0C6B%211030&o=OneUp
https://onedrive.live.com/?authkey=%21APM7hx6Q2ynLu-A&cid=2370B62DDF9F0C6B&id=2370B62DDF9F0C6B%211334&parId=2370B62DDF9F0C6B%211276&o=OneUp
https://www.partsfish.com/oem-parts-for-suzuki
http://gsarchive.bwringer.com/mtsac/~cliff/storage/gs/GS450GA_Owners_Manual.pdf

Suzuki... | Answered on May 14, 2019


Hi, Skcrappy and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the choke.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Quick disconnect check ball stuck.
14. Compression below 75 PSI.
15. A stuck-bent-burnt valve.
16. Improper valve clearance (too tight)
17. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
18. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
19. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
20. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections are loose or connected to the wrong cylinders.
21. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
22. Faulty neutral, clutch, kickstand safety switch.
23. Faulty fuel pump or fuse or relay.
24. Faulty or corroded run/stop switch.
25. Tilt sensor needs a reset.
26. Security system not disarming alarm needs a reset.
27. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.motorcycleforums.net/forum/classics/48972-1980-gs450-starting-issue.html
What To Do If Your Motorcycle Doesn Start
https://onedrive.live.com/?authkey=%21APM7hx6Q2ynLu-A&cid=2370B62DDF9F0C6B&id=2370B62DDF9F0C6B%211334&parId=2370B62DDF9F0C6B%211276&o=OneUp
https://www.partsfish.com/oem-parts-for-suzuki
http://gsarchive.bwringer.com/mtsac/~cliff/storage/gs/GS450GA_Owners_Manual.pdf

Suzuki... | Answered on May 14, 2019


Hi, Adamgs62 for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://gsarchive.bwringer.com/bikecliff/images/bevel_oil.pdf
Suzuki GS850 Secondary Bevel Oil Change
Suzuki GS850G Service Manual
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Suzuki... | Answered on May 14, 2019


Hi, Cosmos322 for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Premix And 2 Stroke Fuel Ratios For Your Dirt Bike
Am going to BLOW UP my dirt bike at this ratio
http://tps.naka-kon.com/1982_suzuki_sp_125_repair_manual.pdf
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Suzuki... | Answered on May 14, 2019


Hi, Djasquirino for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
The Proper Procedure for Breaking in Your Motorcycle
https://www.youtube.com/watch?v=wTCVyYaRu9E
http://apply.cafezupas.com/suzuki_raider_r150_service_manual.pdf
https://www.partsfish.com/oem-parts-for-suzuki
Suzuki Raider 150 FU150SC Owner Manual

Suzuki... | Answered on May 13, 2019


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere $29 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Wiring+diagram+1982+Suzuki+SP500&tbm=isch&source=univ&sa=X&ved=2ahUKEwjzzNP0z5XiAhXH1FkKHS_gDbIQsAR6BAgJEAE&biw=1440&bih=757
Suzuki Motorcycle Wiring Diagrams
https://www.repairmanual.com/product/official-1981-1983-dr500-sp500-suzuki-factory-service-manual-r99500-45000-03e $29
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Suzuki... | Answered on May 12, 2019


Hi, Anonymous and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the choke.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Quick disconnect check ball stuck.
14. Compression below 75 PSI.
15. A stuck-bent-burnt valve.
16. Improper valve clearance (too tight)
17. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
18. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
19. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
20. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections are loose or connected to the wrong cylinders.
21. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
22. Faulty neutral, clutch, kickstand safety switch.
23. Faulty fuel pump or fuse or relay.
24. Faulty or corroded run/stop switch.
25. Tilt sensor needs a reset.
26. Security system not disarming alarm needs a reset.
27. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Scooter Troubleshooting Scooter won start All about Scooters
What To Do If Your Motorcycle Doesn Start
http://staging.isi.org/suzuki_ran_service_manual.pdf
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Suzuki... | Answered on May 12, 2019


Hi, Darrentarlof before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.visordown.com/forum/workshop/rg125-starting-problems
What To Do If Your Motorcycle Doesn Start
https://www.tradebit.com/filedetail.php/267897105-suzuki-rg125-gamma-1985-1996-workshop-service-repair $15
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Suzuki... | Answered on May 12, 2019


Hi, Cecilia_alve and the usual suspects are:
1. Retarded ignition timing.
2. Retarded cam timing.
3. Bent or burnt exhaust valve.
4. Massive air leak.
5. Intake manifold cracked or damaged.
6. Intake manifold seals have failed.
7. Wrong heat range spark plug.
8. Fuel delivery system running too lean.
9. Faulty Map, O2, MAF, TPS, sensors.
10. Faulty advance mechanism.
11. Faulty VOES switch.
12. Aftermarket exhaust headers tubing too thin.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://advrider.com/f/threads/ohh-man-dr650-header-glowing-red.621819
https://thumpertalk.com/forums/topic/583284-is-the-head-pipe-supposed-to-glow-red-in-the-dark
https://www.tradebit.com/filedetail.php/281002326-suzuki-dr600-s-type-sn-41-a $15
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Suzuki... | Answered on May 12, 2019


Hi, Siksavstoli and the usual suspects are:
1. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Faulty main circuit breaker and or connections.
4. Faulty ignition coil and or connections.
5. Faulty spark plug, oil or gas fouled, wrong heat range or service type, wrong gap, loose in the cylinder head, broken electrode or insulator.
6. Faulty spark plug cables, leaking or broken, internal damage check for spark leakage in the dark.
7. Faulty ignition module, switch, CKP, MAP, CMP, sensor and or any connector in the ignition circuit could have corroded, loose, or broken pins/sockets
8. Burnt exhaust valve or air leak in the exhaust system.
9. Improper valve clearance (too tight).
10. Check for generated diagnostic codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.pnwriders.com/threads/suzuki-gs-backfires.161014
https://www.motorcycleforum.com/59-motorcycle-repair/116887-backfire-problem.html
https://onedrive.live.com/?authkey=%21APM7hx6Q2ynLu-A&cid=2370B62DDF9F0C6B&id=2370B62DDF9F0C6B%211334&parId=2370B62DDF9F0C6B%211276&o=OneUp
https://www.partsfish.com/oem-parts-for-suzuki
https://www.manualslib.com/manual/1075262/Suzuki-1982-Gs450ga.html

Suzuki... | Answered on May 10, 2019

Not finding what you are looking for?
2002 Suzuki GZ 125 Marauder Logo

34 questions posted

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5948 Answers

ROB

Level 3 Expert

858 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GZ 125 Marauder Suzuki

  • GZ 125 Marauder Suzuki

Most Popular Question

tail light bulb keeps

  • Motorcycles
Loading...