Question about 2003 Suzuki VS 800 Intruder
How do I add oil to 2003 Suzuki 800 intruder @
Posted by Anonymous on
Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Posted on Mar 11, 2019
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Any changes you make to the exhaust system will alter the sound the bike produces. The more you cut baffles,and open up the exhaust, the louder it will get. What you do alter to a greater extent,is the state of tune of the motorcycle. Any changes to exhaust or inlet plumbing will require a retune of the engine to suit the modifications. This can be subtle to dramatic. Opening up exhausts can often rob low end power where exhaust port scavaging is relient on some back pressure for maximum effect.
Best to work directly with an engine tuner to do the mods that are known you can get away with, or buy aftermarket prebuilt pipes that have a known previously tested state of tune. Nothing worse than doing something, that then costs money to put back the way it was on finding out it didnt work as well as was hoped.. Hope this has helped you steer your custom mods a little. I can say with certainty, that I have ventured to do what you are doing many times in the past, and it has always cost me more money in tuning and... and well more parts :) Cheers
Posted on Jan 20, 2009
No adjusting is possible.
Slip can be caused by several defaults:
- Wrong engine oil ( SAE 10w-40 API SE or SF only )
- Weak clutch springs ( free spring length : 34mm ( 1.34in ) MINIMUM
- Worn clutch disk 2(internal teeths ) ( wear limit 3.15mm ( 0.124in ) ) This is the last disk, against the clutch center
- Worn clutch disks 1 (internal teeths) ( wear limit 2.62mm ( 0.103in ) )
- Clutch plates ( thikcness between 1.55 and 1.65mm / 0.0610 and 0.0649 inches
- Damaged pressure plate ( cracks round the spring holes )
To check the clutch parts, the right engine cover must be removed.
Take attention while loosening the clutch spring bolts!
Drain engine oil, and set engine into first gear ( this locks the clutch for an easy loosening of the spring bolts )
Hope it helps
Posted on Apr 02, 2009
I know for the models till 2002 where the battery is located in front of the rear wheel.
Place the bike on her side stand
remove the negative battery lead at the left side, just below the transmission tube ( cone ) 10mm socket wrench
On the right side remove the security cap on the positive lead ( cross screwdriver ), then remove the positive lead.
The battery is hold in place with a 'floor plate'. remove both bolts of the floorplate ( on each side ) while holding the palte into place.
gently lower the plate and the battery.
I hope the 2004 model has the same assembly!
Posted on Apr 02, 2009
Tips for a great answer:
Oct 12, 2018 | 2003 Suzuki VS 800 Intruder
Dec 04, 2016 | 1996 Suzuki VS 800 Intruder
Feb 23, 2011 | 2003 Suzuki VL 800 Volusia
Jul 25, 2010 | 2003 Suzuki VS 800 Intruder
Jun 10, 2010 | 2002 Suzuki VS 800 Intruder
Feb 21, 2010 | 1996 Suzuki VS 800 Intruder
Jul 06, 2009 | 2003 Suzuki VS 800 Intruder
Nov 03, 2019 | Qlink Legacy 250 Motorcycles
35 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: