Question about 2010 Husaberg FE 390

1 Answer

Quits running 2010 Husaberg FE 390

2010 husaberg fe 390 stops when hot will not start, have to wait for 30 minutes before it will start only runs for a while then stops changed fuel filters still stops @

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Husaberg Master
  • 56,994 Answers

Hi, Anonymous and the usual suspects are:
1. Severely discharged or a damaged battery must have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Faulty alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. A faulty main circuit breaker or ignition switch, check for loose connections and continuity.
5. Faulty system relay or ignition relay, check for continuity.
6. Faulty ignition coil, ignition/electronic module.
7. Faulty CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Fuel tank empty
11. Fuel tank contaminated with ethanol sludge.
12. Water or dirt in the fuel system, or clogged filter.
13. Quick disconnect check ball stuck.
14. Restricted, blocked or kinked fuel line.
15. Faulty fuel pump.
16. Faulty pressure regulator.
17. Faulty or clogged fuel injectors.
18. Lean angle switch is faulty or needs adjustment.
19. Catastrophic engine failure, perform a compression test.
For more information about your issue and valuable "FREE" downloads that you need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://thumpertalk.com/forums/topic/774831-2010-husaberg-390-dying-after-2-days-help
http://www.dirtbikeworld.net/forum/archive/index.php/t-76040.html
https://www.manualslib.com/manual/1235895/Husaberg-Fe-450-Eu.html
http://www.cyclebuy.com/husaberg/parts.htm
HUSABERG FE 450 EU Owner Manual

Posted on Jun 13, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
goofduck
  • 490 Answers

SOURCE: i need 2001 husaberg fe 400 plastics

dennis kirk

Posted on Apr 21, 2009

  • 71 Answers

SOURCE: 1986 Yamaha Radian stops running after 20 minutes

Sounds to me like it could be a few things... pretty interesting that it runs and shuts down...sits for a little while then fires back up. Could be something as simple as a bad ground.. maybe it needs cleaned.. if the ground is making very little contact.. the bike would run bad, and because its direct current it has to flow. The metal in the motor frame etc will hold so much DC current.. but *** soon as it load up the bike would stop sparking. Let it sit for a while, DC trickles into the battery through the slight contact, bike fires back up. OR could be bad venting of your fuel tank, or a partial clog at the pet ****.. the first is pretty easy to check, open your fuel cap and start the bike..if it does the same thing then its not a vent problem. One thing that does happen on the Radian, is the reserve fuel screen inside the tank comes loose, and then everything inside the that has built up over the years either partially clogs the pet ****, or the hose, or both. Take the tank off, pull the pet **** off..if it still has two intact tubes with good screens..you probably don't have any junk in your line..but I would pull the line off and blow through it any way... it could be some type of blockage, when the bike sets the fuel seep through, but when it runs it eventually creates a vaccuum that stops the fuel flow. Those are my two first thoughts... good luck!!

Posted on Jun 07, 2009

epreston
  • 8 Answers

SOURCE: start the bike runs good starts to miss then stall wait a coulpe

Because the problem you describe is intermittent, it is almost certainly fuel related, either the fuel itself or the carbs on your bike.

Before taking it to a dealer or mechanic (or trying to fix it yourself), get a can of Seafoam (I know Autozone has it) and add it to the fuel. It seems to do an excellent job of cleaming out whatever bad stuff accumulates in fuel systems over time, especially carburetors.

There's an interesting review of it at: http://www.webbikeworld.com/sea-foam/

Posted on Aug 02, 2009

  • 324 Answers

SOURCE: Hard to start; when it runs, runs fine. Thinking

overheating

Posted on Jul 04, 2010

SOURCE: honada starts then slowly dies

check fuel system

Posted on Apr 23, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

FE 390. Bike will not go into neutral with engine running. How to fix?


Hi, Anonymous for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix/test or parts inquiry. If necessary transport your vehicle to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your issue. For more information about your issue please visit the website below. Good luck and have a nice day. DOWNLOAD 2010 Husaberg Fe 390

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Oct 24, 2015 | 2010 Husaberg FE 390

1 Answer

How do i test husaberg 400 fe 2001 cdi / ciol if it working or not


Start by sticking the plug to a head bolt for a spark if that don't work the only way u can test it is with a different cdi

Feb 13, 2015 | 2001 Husaberg Fe 400 E

1 Answer

2013 Husaberg 350 Enduro how to adjust the timing


Hi, Barry it's nonadjustable for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.topspeed.com/motorcycles/motorcycle-reviews/husaberg/2013-husaberg-fe-350-ar148843.html
KTM 350 Valve Adjustment And Camshaft Swap
http://www.datamanagement-le-blog.com/fe350_service_manual_download.pdf
https://www.rockymountainatvmc.com/Parts-Finder/11057/2013-HUSABERG-FE-350
https://paitandacent.files.wordpress.com/2015/08/husaberg-fe-350-owners-manual.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Feb 07, 2015 | Husaberg Fe 400 E Motorcycles

1 Answer

2003 Husaberg Fe 650 e no spark


Hi, Lance and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting/leaking, spark plug cable connections loose check for spark leakage in the dark.
6. Faulty ignition coil or electronic control module.
7. Faulty pulse coil.
8. Faulty CKP, CMP, or BAS sensor.
9. Faulty ignition switch.
10. Faulty run/off switch
11. Tilt sensor needs a reset.
12. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2003 FS 650 No spark Husaberg Forum
husaberg what they don want you to know
HUSABERG FE 450 Repair Manual
http://www.husaberg.no/Teknisk%20data%20Husaberg/Delekataloger/Firetakt/2000-2008/2003parts.pdf
Husaberg 400 User Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Mar 06, 2018 | 2003 Husaberg Fe 650 e

1 Answer

My2011 570 seems to run out of fuel and simply stop. After about 5 min it will start then a few minutes latter after riding it simply stops again. It will not start immediately. Tried the basics of taking...


Sounds like you have the common problem of a plugged fuel pick up. You need to remove the fuel pump, pickup, and sender unit deep in the fuel tank. Its quite common for these bikes to come with a substanitial amount of junk in the tank. There are fuel pickup sceens available for the pickup that seem pretty good at preventing this problem form reoccuring. once you remove the pick up unit, clean the screen (usually plugged with plastic mold remnants. You may want to check the injector if it doesn't run 100% after reassembly. Injector fouling is rare nut not unheard of. Husaberg.org is a good forum for owners

May 31, 2011 | 2011 Husaberg FE 570

1 Answer

I was fitting a after market tail light the other nite and had the engine running as to have power to identife wich wire did what (testing with a multi meter) and the engine stoped as if it was switched...


Hi, Jonti16 and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and CDI box.
5. Spark plug cables shorting or leaking, spark plug cable connections loose, check for spark leakage in the dark.
6. Faulty ignition coil, pick up coil, trigger coil or CDI box testing needs to be checked with an ohmmeter at 70 degrees Fahrenheit
7. Faulty safety switches clutch, kickstand, neutral, off/on etc.
8. Faulty ignition switch.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
No spark AGAIN
husaberg what they don want you to know
HUSABERG FE 450 Repair Manual
http://dirtypart.com/manuals/filer/Husaberg/Husaberg%20Repmanual%20-05.pdf
http://dirtypart.com/manuals/filer/Husaberg/Husaberg%202001-2002%20SPARE%20PARTS%20MANUAL.pdf
Husaberg 400 User Manual
HUSABERG FE 450 EU Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Mar 16, 2017 | 2002 Husaberg Fe 501 E

1 Answer

Husaberg 600 wont start on the kick


How much do you weigh? If you have strong compression, that's what you want.

Aug 06, 2009 | 2000 Husaberg Fe 600 E SM

Not finding what you are looking for?
2010 Husaberg FE 390 Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husaberg Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5884 Answers

Marvin
Marvin

Level 3 Expert

85020 Answers

Strech
Strech

Level 3 Expert

1562 Answers

Are you a Husaberg Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...