Question about 1984 Honda GL 1200 Interstate Gold Wing

1 Answer

Loosing hyd pres have to bleed at bottom rebuilds pres use 10/12x's then have to repeate

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Honda Expert
  • 391 Answers

You have a leak somewhere.

Posted on Feb 02, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Thomas skidsteer hyd ran low on oil now will not operate filled hyd sounds like a belt slipping


more like pump cavitating and not good for it at all. dont know how but you need to bleed that air out of there before you trash the pump itself.

Aug 02, 2017 | Cars & Trucks

1 Answer

4496 CASE TRACTOR .Ran out of hydraulic oil , filled up and bleed lines , still have no steering and the brake is out ,.What valve is locked in ?


by bleeding lines where exactly did u do this ? , the place id try 1st is right off the pump to the dist block (carefully!!!) if no pressure there then a more aggressive repurdge of hyd sys is needed using another machines hyd system connected to remotes inputs off the dist block
reason 4 this is that hyd oil pumps don't just pick up oil again when run dry an have to be helped to pressure up again , Also another possible cause is that pressure relief is stuck open , this doesn't allow any pressure to build up

Nov 13, 2015 | Cars & Trucks

1 Answer

2007 gmc c6500 hard brakes, not vacume hyd


if the car has ABS I would look there next.could have a faulty modulator.

Aug 14, 2014 | Cars & Trucks

2 Answers

Why loosing hyd.pres.when riding /lose after bleeding /use awhile loose again re bleed


When I got my Goldwing, I noticed someone replaced the top on both reservoirs on the handlebars. I did the full service on the bike, including changing all hydrolic fluids in the reservoirs. I noticed that the inner diaphragms were missing, causing them to slowly bleed fluid out of the small air hole at the top of the reservoir. I was able to fix this by flipping the inner rubber seal around 180 degrees.(like it was installed reversed)

loosing-hyd-pres-when-riding-lose-after-t0rmh4tkup1vcgvj1n32mfxv-2-0.jpg

Jul 03, 2014 | 1984 Honda GL 1200 Aspencade Gold Wing

1 Answer

I just put oil on my cherrypickers manual hyd ad dosent pump what can i do?


sounds like it has a gut full of air which can be compressed whereas hyd oil cannot and is not circulating. must be some way of bleeding system

Dec 10, 2012 | Cars & Trucks

1 Answer

1994 chevy 3500 1 ton dump hyd problem when I activate the hyd unit, I can hear the pump running, and it seems to develope a load on the motor, but the cylinder does not lift. I had the dump body...


There should be a bleeder valve on the cylinder itself somewhere. Otherwise with air in the system, Im surprised no hyd fluid came out the top of the cylinder!

Feb 05, 2010 | 1994 Chevrolet C/K 3500

2 Answers

Same problem 1988 trooper clutch issues


Have seen em put on with the bleed screw at the bottom by mistake ?

Jul 31, 2009 | 1988 Isuzu Trooper 2 Door

1 Answer

Suzuki atv brake rebuild no pressure


Cylinders, lines and calipers must be bled thoroughly and in order.
Start with the master cylinder.
Break the line loose at the cylinder and tighten it firmly so you can loosen it easily.
pump the lever/pedal several times,(don't worry about pressure yet). Hold the lever/pedal down.
break the line loose slightly, just enough to release the pressure. Re-tighten the line and release the lever.
Repeat this procedure several times. (4-6)
Repeat this procedure at the line just above the caliper.
Finally repeat this procedure at the bleed screw.
This takes a while but will insure that all the air is out of the lines. It dosen't take much air to ruin a great brake job.
Good Luck

Jun 16, 2009 | 1985 Suzuki Rg 250 Gamma

1 Answer

Bleeding hyd system on 05 sebring convertible top


You are probably low on fluid.
Behind the rear seat is your motor/pump/reservoir combination.
With the top down, fill the reservoir to overflowing with ATF.
Cycle the system a few times and repeat.
Do this till the reservoir will take no more fluid.
Check the lines and cylinders for leaks. If you replace any lines or cylinders, always do them in pairs.
Karl at Topgunwon.com

Apr 08, 2009 | 2004 Chrysler Sebring

Not finding what you are looking for?
1984 Honda GL 1200 Interstate Gold Wing Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5954 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

richard libby

Level 2 Expert

209 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...