Question about Maytag Atlantis MAV6000 Top Load Washer

1 Answer

My maytag atlantis washer is 9 years old. It filled up, but will not wash, spin or drain

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

You may have to replace the timer

Posted on Aug 01, 2012

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 290 Answers

SOURCE: Maytag MAV6200AWW does not spin

Be sure to check inside basket very carefully to make sure no loose nails or screws or drill bits etc that were left in a pocket are sticking through a hole in the basket and locking it to tub. This is common. If that is not the problem,one of three things has happened. 1 The thrust bearing that releases the brake has worn out. This is the most common and easiest thing to repair. If you tilt the machine back so you can look under it you will see the pulley that turns the transmission. When the pulley turns one direction it works the agitator, turn it the other direction and you should see it push the brake up that is directly above it. The thrust bearing kit includes the pulley and all bearings and washers to release brake. If you are mechanichal and can follow the directions that come with it, it is a fairly simple repair. 2 The brake lining has come apart and "stacked" itself in the brake housing. Replacing the brake is not hard, but there is about 200lbs of spring force pushing against the brake and housing that must be released slowly. I would recommend you call a technician for this just because I don't want anyone to get hurt trying to follow my directions on this repair. 3 An item of clothing has found its way between the basket and tub and has the basket bound up. This would mean removing agitator and basket. It is not likely this has happened, but I have seen it before.

Posted on Oct 04, 2007

Anonymous

  • 1 Answer

SOURCE: Does not spin

Seems you need a lube job on the centrifical mechanical switch that fully engauges the spin cycle( part of the pully to shaft assembly)

Posted on Jul 08, 2008

Anonymous

  • 4 Answers

SOURCE: maytag atlantis will agitate won't spin

I had the same problem with my Atlantis a couple of months ago. It turned out to be the bearing for the tub drive pulley. When you look under the washer there are three pulleys. The one for the motor is ont he left, the drain pulley on the right and the big one in the middle for the tub. What I found is that when the bearing went bad, the tub would fill and turn for washing, but it would not turn at all for spinning. I could turn the pulley by hand but the tub refused to budge. I removed the main pulley and could see that the bearing had exploded. You can't buy just the bearing but the whole pulley kit is like $35 so I got off easy. I put the machine back together (which is tricky) but it works fine now. The pulley kit comes with complete instructions but it's really straightforward. The tricky part is that you have to pull down on the end of the drive shaft in order to get the retainer ring onto the pulley. That can be difficult if you don't have a lot of room to work or have a partner to assist. You can replace the whole thing or just the bearing and save the pulley for a rainy day if you want. I opted for the whole replacement. But I saved the old. cause ya neva know!

Posted on Jan 16, 2009

Anonymous

  • 1 Answer

SOURCE: maytag washing machine #mav6260aw

I found the crazy sound where comes from, it was an aluminum ring in the drain pump.
First of all, I took out the belt under the bottom, checked moter to run itself, it was fine, so, I suspected some waste in somewhere, it was lucky I disassembled the drain pump first, no waste in the drain pump, but I saw a ring that was cut under the pump (seems should be connected), when I try to spin the pump wheel by hand it is broken because of the ring.
I ordered the entire drain pump on the website, the cost $74 + delivery fee, I recognized Maytag re-designed the drain pump due to the ring ( new pump does not have the ring anymore). Now the washer works fine like new.

Posted on Mar 11, 2009

Anonymous

  • 1 Answer

SOURCE: Maytag Atlantis MAV6200AWW; Washer goes through

Maytag Atlantis washer goes thruout washing cycle,but dosen't simse or spin....

Posted on Jun 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag atlantis washer(spinning problem)


Your problem sounds like a broken belt . Check and replace. Good Luck Friend.

Jan 25, 2018 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

I have a maytag Atlantis washer - 7 years old, it


I have a Maytag Atlantis top load washer which leaks in the rear right hand corner under the discharge hose, how do I take the machine apart to get to the problem.

Feb 04, 2010 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Water will not drain, will not do anything.


I would check the lid switch. That is most likely the problem.

Apr 28, 2009 | Maytag Atlantis MAV6451 Top Load Washer

1 Answer

Maytag top loading washer won't agate. Instead it fills with water and spins, then drains, fills for the rinse and spins. Thanks Bill


Open your control panel.
Disconnect then reconnect your timer wiring harness.
If this does not correct the problem,replace the timer.

Feb 25, 2009 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Maytag atlantis washer


Start by checking the belt by tilting the machine back and examining for wear, glazing and cracks, next pull the belt to make sure everything turns. Post back if this looks fine.

Jul 26, 2008 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Maytag Mav-1 Slow Spin


hi thanks for the question with any washer if you use a hi sud zing detergent it really slows down the spin cycle check this just fill & drain 2or 3 times use some veniger try this thanks the appliance doc

Jul 17, 2008 | Maytag Atlantis MAV6451 Top Load Washer

Not finding what you are looking for?
Maytag Atlantis MAV6000 Top Load Washer Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...