Question about Bush Office Equipment & Supplies

1 Answer

Hi, I have a Bush DWFS126W and keep getting an E7 error code. Any advice?!?!?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,345 Answers

For an E7 fault the PCB has to be reset:

1. With the door open, turn the appliance 'On'
2. Within 3 secs, push the program selection button 'P' 4 times
Good Luck Clive

See this: http://www.fixya.com/support/t25937477-error_codee7

Posted on Jan 12, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: AR-5132 Error code E7 13

netoiyer les miroire de scanner et la bare blanve

Posted on Dec 19, 2008

Anonymous

  • 95 Answers

SOURCE: ERROR CODE E7-03

E7-03 indicates hard drive trouble. the hard drive is going bad. There is not a whole lot you can do besides trying to reseat all connectors for the hard drive (the harness/wire from the HDD to the ICU PWB board) otherwise replace the hard drive.

Posted on Mar 28, 2009

Anonymous

  • 2 Answers

SOURCE: sharp ar-m205 error code E7 11

U HAVE TO UPGRADE THE FIRM WARE BY ENTERING SIMULATION 49-1 THE VALUE IS d THEN UPDATE THE FIRM WARE IF U HAVE IT

Posted on Jun 06, 2009

Dany Moldo

  • 74 Answers

SOURCE: cannon pixma mp145 printer error code e7 & e2

E2: Reload the paper correctly and press [Black] or [Color].

E7: The cartridges are not installed in place.

These are from the manual.

Posted on May 10, 2010

ercupa190

ernesto cuadra

  • 12223 Answers

SOURCE: error code E7

Dear Sir:

This error is normally associated with1) Elevation Motor problem.2) Display doesnot light up

1)tigh the connector from elevation motor and clean 2) Adjust the Potentiometer 3) Lubricate the gear 4) Test it.

2) Adjust the Reed switch see the diagram attached 3) tigh the connector very weel and clean the reed s.and reset.

sincerely. God bless you.
4_23_2012_10_09_09_am.gif

Posted on Apr 23, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My. Bush dishwasher won’t drain, it’s also beeping code e7


E7The appliance is waiting for a signal from a flow meter. However this appliance is not fitted with a flow meter. See below for details on how to cure this fault.

For an E7 fault the PCB has to be reset:
1. With the door open, turn the appliance 'On'
2. Within 3 secs, push the program selection button 'P' 4 times

Jan 05, 2018 | Bush Dishwashers

1 Answer

Bush dishwasher DWFS126W displaying E3


This error indicates a flood in the base of the machine. It maybe the float jammed in the Up position, especially if you have moved the machine.

Mar 28, 2017 | Bush Dishwashers

1 Answer

I need instruction manual for Bush dishwasher DWFS126W


Visit their website and search for the manual on their support page.

Nov 23, 2014 | Bush Dishwashers

1 Answer

Hi my copier displays E7


Check this out :
E7 codes deal with the optical scanner unit and or the laser unit. It could also be the lamp in the scanner unit. The E7 is the main code. There is a sub code associated with it. To view the sub code hold down the start button. Below is a list of specific codes and their meanings:
E7-02: LSU trouble
E7-10: Shading trouble (Black Correction)
E7-11: Shading trouble (White Correction)
E7-12: Shading Trouble
E7-16: Abnormal laser output
If it is a laser (LSU) issue then the LSU may need replacing.
If it is a shading error the first step is to remove the platen glass carefully (with the power off because the inverter board). There is a thin white strip on the bottom side of the platen next to the **** glass. Clean this white strip with a soft cloth and a small amout of isopropyl alcohol.
Dust on the optics can also cause shading reference errors so gently blow off the mirrors with canned air.
Perform the following key procedure to reset error:
"#" key, Interrupt key, "C" key, Interrupt key
"1" key, "4"key
Start key, "CA" key.
See if unit cycles and comes back up. If not turn off and then back on the main power.
If error reappears on site technical service may be required.

Oct 31, 2010 | Sharp AR-5316 Advanced Digital Imager...

2 Answers

How to remove erro code E7


Code E7 has got sub-codes. Go and press copy button to see the sub-code and then report it. Generally, this concerns the laser unit and i would advice you to clean the optical platen glass from interior and screw back well. If a code occurs, then report it for more help.

Mar 09, 2010 | Sharp AR-5316 Advanced Digital Imager...

3 Answers

AR-5132 Error code E7 13


CCD calibration error. Make sure the optics are clean in the machine in the scanner and free of dust.

Nov 03, 2008 | Sharp AR-5316 Advanced Digital Imager...

3 Answers

E7 problem


E7 codes deal with the optical scanner unit and or the laser unit. It could also be the lamp in the scanner unit. The E7 is the main code. There is a sub code associated with it. To view the sub code hold down the start button. Below is a list of specific codes and their meanings:
E7-02: LSU trouble
E7-10: Shading trouble (Black Correction)
E7-11: Shading trouble (White Correction)
E7-12: Shading Trouble
E7-16: Abnormal laser output
If it is a laser (LSU) issue then the LSU may need replacing.
If it is a shading error the first step is to remove the platen glass carefully (with the power off because the inverter board). There is a thin white strip on the bottom side of the platen next to the slit glass. Clean this white strip with a soft cloth and a small amout of isopropyl alcohol.
Dust on the optics can also cause shading reference errors so gently blow off the mirrors with canned air.
Perform the following key procedure to reset error:
"#" key, Interrupt key, "C" key, Interrupt key
"1" key, "4"key
Start key, "CA" key.
See if unit cycles and comes back up. If not turn off and then back on the main power.
If error reappears on site technical service may be required.

Jan 06, 2008 | Sharp AR-5316 Advanced Digital Imager...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bush Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

The Knight
The Knight

Level 3 Expert

76140 Answers

Terry
Terry

Level 3 Expert

10347 Answers

Are you a Bush Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...