Question about Hoover Washing Machines

Open Question

My hoover F7411900 doesnt work on wash .doesnt put water out

But if i put on rinse it works like it should

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1462 Answers

SOURCE: hoover washing machine top load, model 550m.5.5kg

water leak from cold hose nothing to do with other problem. tighten hose connection and fit a new hose washer overfilling probably because air chamber blocked. remove lid. you will see a pressurestat somewhere at the top - usually round with anything from 3 to 7 wires and a small tube underneath. follow hose down and it connects to the air chamber. make sure this is free of gung and check hose for splits and has no blockage. to check the pressure stat itself, attach your own hose to the stat and while machine in fill mode, blow down this hose and you should hear a click and water intake will stop

Posted on May 04, 2007

Ad
reddevil6
  • 1673 Answers

SOURCE: hoover 500 top load washing machine - water in-flow very, very slow

Check the water valve. Most of the hoses that are hooked to the water valve have a screened filter, turn water off, unhook hoses, check to see if they need to be cleaned. Other wise the water valve is bad and will have to be replaced.

Posted on Jan 18, 2008

  • 351 Answers

SOURCE: hoover 600mb 6.0 kg top load washing machine (not as below)

timer or timer module fault

Posted on Mar 02, 2008

  • 228 Answers

SOURCE: Washing machine doesnt rinse and spin

IT SOUNDS AS THOUGH ITS NOT HEATING IF IT DOESNT IT STAYS IN WASH MODE AND WONT COMPLETE CYCLE NEW HEATER REQUIRED

Posted on Aug 12, 2009

  • 3 Answers

SOURCE: hoover optima hnf6167 7kg washing

My washing machine completes its cycle but is leaking water from the left hand side on to the floor, Why is this???

Posted on Apr 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hoover F7411900 was full of hair.cleaned out filled soap and water not spraying but suction good not sure what else to do


suck up some warm clean water while moving the wash rinse button back and forth thid will unplug the hoses if that dosent work replace the switch

Aug 26, 2018 | Cars & Trucks

1 Answer

I have a model f7411900 steam vac from Hoover and it started making a loud noise like a broken belt does in a vacuum. Does this have a replacement bely


Open the product, make sure first that it is not something stuck inside. If it is a belt, check with amazon. Just make sure that you have the correct model.

Aug 24, 2016 | Hoover F7411900 Maxextract Dual V Carpet...

1 Answer

Brushes on my hoover spinscrub model F7411900 wont spin


vanger cheva in post 1 got the correct answer. I just disassembled my f7411900 with some difficulty and took the turbine apart. Sure enough the bearing on the shaft was froze from rust. I was able to free it up in a vice and screw driver big enough to grab and turn the middle of the bearing. I used 3-1 oil and it now is smooth again. Not sure for how long. It was then I found the instructions by vanger above. There is no belt in this unit. The turbine is driven by water that turns the brushes.

Sep 13, 2012 | Hoover Vacuums

1 Answer

What setting do I need to have the machine on to **** up the excess water? I want to download the manual but can't seem to find a link to do so, how would I do that?


You should have the vacuum set to Wash/Rinse for all steps in cleaning. Press the trigger to release the cleaning solution and push the vacuum forward. With the trigger still pressed, bring the vacuum back towards you). Then release the trigger and again move the vacuum forward and then back. Repeat the "dry" strokes until the dirty water enters the dirty water tank. Watch the water going through the dirty water tank lid. Empty the dirty water tank if the suction fails or the tone changes. Do more dry strokes after cleaning the entire surface until you do not see more water entering the dirty water tank.

The manual is available from Hoover at the product site: http://hoover.com/products/details/f7411900/max-extract-dual-v-widepath-carpet-cleaner/ . The direct link is here: http://hoover.com/file/592/ .

I hope this helps.

Cindy Wells

Aug 08, 2011 | Hoover SteamVac F7411-900 Upright Vacuum

1 Answer

F7210-900 Steam Vac. will not put out water when switch is in wash position but it will put out water when the rinse position


There are two electrical solenoids inside the hood assembly. One opens to dispense rinse water, and the other dispenses the soap and water solution. It is likely that the soap and water solenoid has failed and will require replacement. A "work around" fix for this is to mix the soap solution in the clear water tank ( 5 oz. of shampoo per gallon of water ), and shampoo that way until the solenoid can be replaced.

Mar 15, 2011 | Hoover Vacuums

2 Answers

We have a Hoover select 1500 washing machine. It still washes and rinses ok, but doesn't then move onto the spin cycle. But I can manually set the dial to spin and restart it. It then spins fine. I assume...


Could be but also could be rinse water valve not operating due to faulty solonoid. it does a final rinse / softner before spinning if valve faulty then no spin advance....

Nov 11, 2009 | Washing Machines

1 Answer

My hoover washing machine won't spray rinse or deep rinse on cold


Rinse cycles are normally with cold water only.

I believe you have a faulty cold water inlet valve. To confirm, put the machine on a cold only wash cycle, and see if it fill up with water.

If it does, then the valve is O.K. In that case the problem you are having with the rinse cycle is most likely a timmer fault.

Good Luck
Ash

Oct 23, 2009 | Hoover Washing Machines

1 Answer

Water not getting to powder dept


SMALL SPRING HAD COME LEVER THAT IS CONNECTED TO WATER RELEASE VALVE , RECONNECTED SPRING AND EVERYTHING SEEMS TO BE WORKING OK .

Oct 05, 2008 | Hoover H130E Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1479 Answers

jimorris77

Level 3 Expert

411 Answers

Steve F

Level 3 Expert

1254 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...