Question about Kyocera Office Equipment & Supplies

1 Answer

How to instruct kyocera mita 2030 to add toner.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Go into service mode and use simulation 130. it will supply toner for about 5 minutes

Posted on Jun 13, 2019

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 25 Answers

SOURCE: kyocera mita km-2030 call service error

open the left side door and push in the drum unit firmly. it's the part above the waste toner

Posted on Nov 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I hit duplex, then 2 sided and get a cannot combine error


Right, you can't use both at the same time. Try only one at a time.

May 10, 2015 | Kyocera Mita KM 1530/ 2030 Copier Machines...

1 Answer

Call for Service ...... C710


Hi there
I have found various documents which may help you with this problem and possible future problems. This page:
Error Codes Kyocera Mita KM1530 Code C710
can find any code connected with Kyocera mita machines by changing the machine and the error code in the appropriate drop down menus. C710 is identified as:
Description Toner sensor problem
• The sensor output voltage is outside the range of 0.5 to 4.5 V during toner control.
• The toner sensor control voltage cannot be set within the setting range when maintenance item U130 is run. Causes Defective toner sensor. Poor contact of the toner sensor connector terminals. Developer problem.
Another page showing error codes and their meanings is here;
Kyocera Mita Error Code Messages
and this confirms the above.
Also the link below takes you to a Kyocera web page where you can download various manuals for this machine (KM-1530). By changing the product in the drop down menu to KN-2030 you can get similar manuals for this machine.
Download Center
In your question you mention "Compatible KP23153 Black Toner Cartridge 106153" and that led me to wonder if the compatible cartridge is the cause of your C710 error since that is toner related.
Might be worth trying an original cartridge to see if the error goes away.
Hope this is helpful, if so would you please register that with Fixya
Cheers

Nov 24, 2014 | Kyocera Mita KM 1530/ 2030 Copier Machines...

1 Answer

How do I clean spilled toner from the inside of a Kyocera mita copier?


Try using a small soft brush to brush it off while using a good hepa filter vacuum to remove the toner at the same time. Wear a good breathing mask to protect your lungs!

Aug 06, 2014 | Kyocera Mita KM 1530/ 2030 Copier Machines...

1 Answer

I Keep getting a j10 display when I try to print on the display


A J10 shows up if there is no feed from the upper paper tray. Check the operation of the paper feed clutch for the upper drawer.
Good luck,
Peter

Dec 18, 2013 | Kyocera Mita Mita Copier Toner Cartridge...

1 Answer

We have a Kyocera Mita KM 1510 and I am getting an error code C710 and the add toner light is on. I put in a new toner cartridge but the error message and the light are still on. Any suggestions?


C 710 is a Toner Sensor Problem

Defective toner sensor - Replace toner sensor

Poor contact of the toner sensor connector terminals - Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace cable.

Developer problem - Replace developer.

Apr 07, 2011 | Kyocera Mita KM 1510 Laser Printer

1 Answer

UNKNOWN CODE


when ap code is coming add toner. when the toner is empty this code displays.

Nov 23, 2008 | Kyocera Mita KMR-1810P Laser Printer

1 Answer

Kyocera mita km-2030 call service error


open the left side door and push in the drum unit firmly. it's the part above the waste toner

Nov 03, 2008 | Kyocera FS-2000D Laser Printer

Not finding what you are looking for?

Open Questions:

Office Equipment & Supplies Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

gggg

Level 3 Expert

904 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...