Question about Washing Machines

Open Question

I got a proaction machine but when i start it the light comes on then after a min the rinse light comes on they are both flashing and it will not go any further

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1294 Answers

SOURCE: flashing power light and rinse hold light

Check your exit hose spigot, it may be clogged. This is if your filter is all clean. There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it. Snaking out your standpipe would be good too.

Rate me pl.....if helped.

Posted on Jan 26, 2008

Ad
  • 1 Answer

SOURCE: aeg 76669 oko lavamat machine not


I have had the same problem. If you switch the machine to off and then to cotton/linen 95, then press at the same time prewash, soaking, qick wash and stain buttons for 10 seconds switch it off. When I switched it on it worked.

Posted on Jun 24, 2008

  • 2 Answers

SOURCE: Washing machine problem

my w830 is doing exactly the same thing.

I am usually pretty good at fixing these sort of things so if/when I solve it I will post back here.

I think it is a motor fault - most likely the motor brushes are worn out.

Posted on Aug 07, 2008

  • 1 Answer

SOURCE: Flashing lights on Hotpoint FDW20P Dishwasher

No solution! tried resetting to factory defaults but ended up that even the drain pump stopped working. after flooding the kitchen (nearly). I decided it was terminal and am loking for a new dishwasher urgently as I type. Cheers.

Posted on Feb 19, 2009

  • 174 Answers

SOURCE: karcher k 2.36 smoking and flashes of light inside the machine.

Hi:
This sounds like a short circuit or motor problem. They are relatively easy to take apart. If you see a burned wire or connector this can be repaired. If not, it is the motor and probably too expensive to repair considering the price of a new one.

Posted on Jul 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Indesit washing machine function lights ruppidly flashing in the middle of washing cycle


Possible that the inlet filter or the valve is blocked and so there is no or less flow at the time of rinse cycle. Please remove and reset the valve.
click on : Inlet valve.

Jan 19, 2013 | Washing Machines

1 Answer

I am trying to start a cyle and everytime i push the cycle button it does not light up and the quick rinse button comes on and flashes nothing works at all if i push heavy wash it comes on and nothing...


You haven't told me how many times the light flashes, but I will take a guess that this is an error code associated with the water entering the machine being too cool. I believe the machine expects the water to enter at 110 degrees F (43 Degrees C).

To clear the error, press "Heated Dry" then release, then press "Normal Wash" then release and repeat this sequence until all the lights on the machine go solid green. Once this happens, hit ""Cancel" and the machine will reset.

The fix for the root of the problem is to increase the temperature of the incoming water in future (Turn up your water heater temperature a little)

Jul 05, 2011 | Kenmore Elite Stainless Steel 24" BuiltIn...

1 Answer

Iwde12 indesit, not selecting programmes not releasing water, not drying


Hi, I have an indesit IWDE12, I programme the washer which then starts to spin with no water, after 2-3 mins the rinse light, the clock light and the door lock light start to flash and tha washing stops. Does anyone know what this problem could be?

Jun 15, 2010 | Indesit W 123 Front Load Washer

1 Answer

Cda cw494 dishwasher it runs for about 20 mins


is the light indicator flashing because you need to add salt or rinse aid.i have a bosch and my lights only flash to give me information on addig salt and,or rinse aid. so i can stop this by setting my dishwasher to take all in one detergent ,then the lights will not flash.

Nov 10, 2009 | Dishwashers

1 Answer

Flashing lights on Hotpoint FDW20P Dishwasher


No solution! tried resetting to factory defaults but ended up that even the drain pump stopped working. after flooding the kitchen (nearly). I decided it was terminal and am loking for a new dishwasher urgently as I type. Cheers.

Feb 18, 2009 | Hotpoint 24 in. DWF32P Free-standing...

1 Answer

WF540 - Won't work and rinse hold and wash enhance lights flash?


Hi ya, just a quick suggestion, have you cleaned the filter on the front of your machine?? My machine did this and it was only when i cleaned the fluff and the 5 pence pieces from this filter it stopped, Hope it helps
Dobby

May 11, 2008 | Hotpoint Aquarius WF000 Front Load Washer

2 Answers

Indesit WIL143S flashing lights


sounds like your power board is damaged. Did you get any washes out of it before it went wrong

Oct 08, 2007 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Brad Brown

Level 3 Expert

18108 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...