Question about Beko Washing Machines

Open Question

I have a beko washing machine wmd 78127 with flashing degree symbol after temperature and after some timeit goes to pause cant start

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 6 Answers

SOURCE: beko WMA 1715s - won't respond

door lock switch could be your problem..

Posted on Aug 30, 2008

Ad
barkencoa

Barry Coates

  • 3463 Answers

SOURCE: Hotpoint WMD washing machineFault Code F01 machine will not start

Fault code F01 indicates a problem with the motor triac.
Check all connections to and from the motor, the control module, and the motor plug

Posted on Jan 09, 2010

samesymptom

  • 1 Answer

SOURCE: beko wm6152w turn machine on

try holding the start/pause button in for five seconds, hopefully it will restart

Posted on Aug 29, 2010

john_cross

  • 6277 Answers

SOURCE: BEKO wma 250s washing machine does

Hi from retired Englishman in SW France,
This sounds very much like the belt is broken or the motor is malfunctioning.
Belt first.
Belts are not expensive- sorry I do not know how much yours would cost- and are easy to be changed by a competent person:-
REMOVE POWER FROM THE MACHINE AND REMOVE THE BACK.
The motor support bolts should be loosened and the old belt removed. Often putting the new belt on is a bit of a struggle, even with the motor 'loose', because it is new and smaller!
Once on it should be tensioned by pulling the motor against the belt firmly- but not over tight- and the motor support bolts tightened.
ON NO ACCOUNT SHOULD ANY FORM OF LEVERAGE BE USED TO TENSION THE BELT. THAT COULD LEAD TO DAMAGE TO THE BELT, MOTOR AND BEARINGS- EXPENSIVE!
If it turns out to be the motor, it is false economy to just have the brushes changed although financially very attractive. Experience of others is that the brushes may only last months unless, that is, the motor is totally refurbished at the same time. It depends on how old the motor is and how much wear the commutator has had. New motors are not cheap, though. It's your choice!

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

Posted on May 07, 2011

john_cross

  • 6277 Answers

SOURCE: beko wm 5140 washing machine is starting its cycle

Hi from retired Englishman in SW France,

(no promises but it's worth carrying this out anyway!)

I would gently suggest as a first step that you clean the drain motor/pump lint tray/filter. So many 'faults' are caused by blocked filters and many machines will not even go to rinse or spin or release the door lock if there is any water still left inside.
Following are my complete and generic guidance notes for checking both the drain motor filter and the drain motor ;-0)

REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT (alternatively use a wet vac as sensibly suggested by VinnyB1234!)
If you are unsure where the filter is, it is often behind the front lower (kick) panel (or in some machines at the rear in an awkward position!). These panels are either held on by (plasic) screws or will just pull off. Most filters are held in by a round cover/knob. Sometimes the filter will not come out with the cover and you will have to persuade it to come out to play.
It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. Using something suitable like a glove see if it is easy to briefly slow the motor down. If it is easy then the motor is malfunctioning.

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

Posted on Aug 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My washing machine was switched off mid cycle. Now the start/pause, ready, wash & spin/end buttons are lit up. I have switched it on and off from the mains. No change. It is a beko wm6123w. Please help


Try looking in the troubleshooting section of the products user guide/instruction manual, if you have lost this, you can normally download a copy from the manufacturers (beko) website, this is normally located in the support section of the websites.

have you tried pressing the start/stop button as the cycle maybe simply paused.

WM6123 Washing Machines Beko

Jul 04, 2014 | Washing Machines

1 Answer

How to reset beko wm5120w washing machine


You need to get the dial to 90 degree program then push the start and on button together. Keep hold the start button then a light will flash. Then move the dial to spin/drain option and press start to start the reset test mode. Hope this helps.

Aug 17, 2012 | Beko Wm & Wma Models Washing Machine Motor...

5 Answers

How to reset or unlocked the beko washing machine timer


My washing machine time delay switch is flashing and I can't turn the machine on what do I need to do?

Feb 07, 2012 | Beko Washing Machines

1 Answer

Hello, I have a beko WM5120W Washing Machine, and when I try to use the quick wash programme, it does the washing cycle ok, but when it starts the rinse programme, it pumps the water out ok, but when water...


hi
the water level switch or sensor does not activate to tell the programmer that there is plenty water so that it can start to rinse ( what you doing is simply overriding the system .

Dec 31, 2017 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Beko Washing Machines Experts

Eric Taylor

Level 3 Expert

590 Answers

Cindy Wells

Level 3 Expert

6046 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Beko Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...