Question about Mitsubishi WD-65731 65" HDTV

1 Answer

Red Status Light

I turn the power on and it tries to start. There is no picture and the fan runs a little bit. After about 30 seconds, the green timer light turns off and the red status light turns on. I've tried changing the bulb with the same results. When reset, the green light flashes and goes out but when re-powering, results are again the same. I've tried disconnecting from the power for several days, same problem. The owners manual said to take it to a service rep. I am hoping to avoid that cost and challenge. Any advise? Thanks.

Dan

Posted by on

  • Anonymous Mar 17, 2014

    green power light comes on, them after a couple of minutes the status loight turns red - no picture.

  • Anonymous Mar 17, 2014

    green power light comes on, them after a couple of minutes the status loight turns red - no picture.

×

Ad

1 Answer

Hi we have a 52 inch mitsubishi high definition tv and ours did the same thing,we had a repair man out here and he said it was the engine in the tv which we never knew tv's had engines so i contacted mitsubishi cause we didn't take a entended warranty and told them that it was not even 3 yrs old and they should stand up to there products and they did they paid for the part which was 600 dollars and we had to pay for labor....we thought it was the light to and ordered one and it wasn't it was doing the same thing yours did .....

Posted on Jan 13, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my Mitsubishi XD221U projector have a power light blinking red and green?


Reset the lamp timer by holding power and menu button down for 25 secnnds

If you need further help, reach me via phone at https://www.6ya.com/expert/gary_693301a25d57d47d

Sep 03, 2014 | Mitsubishi XD221U New

1 Answer

I have a Sony KDS-R50XBR1 that has no picture. When I turn on the TV, the green Power/Standby LED light blinks for about 30 seconds, then turns red and blinks five times. The Power/Standby LED repeats...


  • Five blinks - AKB circuit (automatic kine bias), the timer/standby indicator blinks for about 30 seconds then goes to the self-diagnosis function. Something is wrong with the video. Check video out, Q705, 732, 761 and other components on the C board, also check Q218, 219, 220 on the A board. In addition, unit could be in IK blanking, try turning up screen A2 slightly.

Jan 19, 2011 | Sony KDSR50XBR1 50" Projection HDTV

1 Answer

Turned on TV and had no picture. Now when I reset I get green blinking light then solid green status. After about 30 seconded red lamp light comes on. Is there a solution?


Your lamp is defective, incorrectly installed, or the cooling fan under the lamp is not cooling the lamp for some reason. Service that area.

Jun 26, 2009 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

Sony- KDF-50E2000


Have you replaced its Lamp?
Symptoms shows TV needs new lamp.
Please always buy original Sony lamp for replacement.

Mar 15, 2009 | Sony KDF-E502000 50" HDTV

2 Answers

Blinking Light on Mitsubishi SL4SU Projector


To jmatthews

Both power light and status light a solid red with no response to any buttons indicates the bulb timer has expired. You need to reset the timer by pressing and holding the left arrow key, the right arrow key and the power button all at the same time for a few seconds.

If there are no problems, the projector will fire up, but you must replace the bulb as it will fail soon and perhaps explode when it does.

Take care

Oct 28, 2008 | Mitsubishi SL4SU ColorView Multimedia...

2 Answers

Lamp will not come on


try pressing and holding the enter button on the projector for about 30 seconds - this resets it. It worked for me!!

Feb 10, 2008 | NEC VT460 Multimedia Projector

Not finding what you are looking for?
Mitsubishi WD-65731 65" HDTV Logo

429 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1257 Answers

The Knight
The Knight

Level 3 Expert

76100 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...