Black & Decker Garden - Recent Questions, Troubleshooting & Support


Black & Decker would be a possible source.

Black & Decker... | Answered 3 days ago


Searched and searched for this, finally found someone's description on an amazon review of the replacement battery. Reprinted below. Worked for me!

1. First use compressed air to blow out the six screw holes that secure the cover to the chassis. If, like me, you don't have a compressor, just tip the mower over so gravity will allow the dead grass and chaff that fills up the screw wells over time to fall out as you dislodge the stuff with a screw driver or a stick.

2. After the debris is removed, use a T20 Torx driver to loosen the screws. There is a slot in the cover screws that allow the use of a blade screwdriver, but you'll need the T20 driver to remove the battery anyway. The screws need not be removed from the screw wells in the cover, but they have to disengage from the chassis.

3. The cover should easily lift away from the chassis once the screws are loose. Expect to find a lot of grass clippings and cobwebs on the motor housing and the rest of the chassis that could benefit from some cleaning while you've got the cover off.

4. As mentioned before, a T20 driver will be required to remove the two screws securing the battery bracket. No slots in these screws. Make note of the positive and negative terminals of the old battery so you can make the same connections to the new one.

5. My replacement battery was smaller (not as tall) as the original. I made a shim out of some old cardboard to allow the bracket to be sufficiently tight. Without the shim, the bracket screws were too long. A piece of 1x wood might work as well, but I liked the give in the cardboard to get a snug fit with the bracket.

6. Replace the cover, tighten the screws, and you should be good to go.

Black & Decker... | Answered on Aug 25, 2019


  • there is a safety on it that has to be pushed down before you pull the trigger to start it. if that safety has a problem or is not fully depressed it will cause the weed eater not to start

Black & Decker... | Answered on Jun 15, 2019


1. Push the mower down to its lowest mowing position.
2. Turn it up on its right side, so the left side is in the air.
3. The existing flap is held in place with a glob of glue at the left (now top) end. Remove the glue by whatever means you like. I "chiseled" at it with taps from a flap-blade screwdriver and hammer.
4. Now you can slide the remnants of the old flap out and slide the new one in. You'll have to bend it slightly even with the mower in its lowest position to get it past the wheel, but it shouldn't be close to breaking.
5. Replace the glob of glue with whatever you have handy that plays well with plastic and rubber. By coincidence I already had DAP Alex Ultra 230 Black loaded in my caulk gun - worked fine.

Black & Decker... | Answered on May 11, 2019


Contact Black & Decker directly to inquire.

Black & Decker... | Answered on Mar 28, 2019


Me too!!! ??

Black & Decker &... | Answered on Dec 17, 2018


fuse probably went in the plug/extension-replace plug and mend the cable or replaceit

Black & Decker... | Answered on Sep 25, 2018


open the covers while unplugged and see if a wire came unplugged

Black & Decker &... | Answered on Sep 05, 2018

Not finding what you are looking for?
Black & Decker Logo

2,765 questions posted

Ask a Question

Usually answered in minutes!

Top Black & Decker Garden Experts

gggg

Level 3 Expert

904 Answers

Nick Olsen

Level 2 Expert

195 Answers

Cindy Wells

Level 3 Expert

6026 Answers

Are you a Black & Decker Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...