Cameras - Page 8 - Recent Questions, Troubleshooting & Support


Did you disconnect from some sort of USB device without umounting it first? Have you tried starting up in Safe Mode? Can you give us a clue to what device you using? Have you updated to the newest software? Do you have any program running that might cause problems...such as a Launcher?

Cameras | Answered on Jan 07, 2019


This is a problem with many different manufacturer cameras, including Nikon. I simply don't do anything unless the blade that does not retract is interfering with a proper photograph, in which case I just open it manually with slight finger pressure. Many Canon point and shoots have legendary leaf problems, and a little pressure opens them quickly. Don't try to repair it. That's when people get into trouble. Some people suggest blowing air but most people use a spray like Dustoff which has oil in it, so I don't recommend that. If you have a quality bulb-type air blower, they are very effective. What works best for me however is a vacuum cleaner and the little attachment that is for getting between shade slats.

Nikon Cameras | Answered on Jan 07, 2019


Have you installed the latest Firmware from GE online?
If you have, are you certain you are not shooting in some Automatic mode that allows the camera to choose its own setting? If you are in FULL MANUAL mode, and you have the very latest Firmware installed, if you are in Flash OFF setting when you turn the camera OFF then it will return to Flash OFF when the camera is turned ON again.

GE Cameras | Answered on Jan 07, 2019


We would stand a better chance of offering advice if we knew the make and model of your camera. The instructions for this should be in the manual anyway.

Cameras | Answered on Jan 06, 2019


If you are looking for one, try Google.

Cameras | Answered on Jan 06, 2019


Has this anything to do with cameras ?

Cameras | Answered on Jan 06, 2019


Is the Write Protect switch set on the card, by any chance ? If not, try a different card.

Cameras | Answered on Jan 06, 2019


Why make this enquiry in a forum dedicated to Cameras ? You may have a better response posting in one dealing with Domestic Appliances - or, failing that, look in the manual.

Cameras | Answered on Jan 06, 2019


The Getting Start Guide and the Camera User Guide are available on the product support page in the manuals section: https://www.canon.co.uk/support/consumer_products/products/cameras/digital_compact/powershot_sx_series/powershot_sx430_is.aspx?type=manuals&language= . You will need to accept the Canon terms of use to download the manuals. The document covers the SX430 IS and SX432 IS cameras.

I hope this helps.

Cindy Wells

Canon Cameras | Answered on Jan 06, 2019


There are exceptions to this. For example, adjusting the White Balance is not available in the 4K Photo mode. See page 197 of the Advanced User Manual: ftp://ftp.panasonic.com/camera/om/dmc-zs60_adv_en_om.pdf .

I hope this helps.

Cindy Wells

Panasonic... | Answered on Jan 06, 2019


We don't and never have, I would ask Canon.

Canon Cameras | Answered on Jan 06, 2019


Find free how to download xmeye for pc a free software for remote video surveillance. Get more information at http://SoftLister.com

Casio Cameras | Answered on Jan 06, 2019


It most certainly could be the camera miss reading the card. However, lately many of the sd cards I have purchased can't be formatted. If you have a PC/Laptop you can re-format the card and then try it in the camera.

Lumix Cameras | Answered on Jan 06, 2019


Likely not enough light to autofocus. Try manual focus to confirm. Can also indicate insufficient battery.

Nikon Cameras | Answered on Jan 05, 2019


About the HS10 autofocus problem, I discovered the cause and solution. It is a problem of camera design, and is caused by three screws securing the CCD sensor. These screws are not properly secured and the vibration eventually dropping.
In two cameras with the same defect, the screws were loose. These screws adjust the sensor position relative to the lens and the sensor is loose when out of position not allowing proper focus.
The solution is to disassemble the camera and secure the screws.
These screws can not be too tight they need to be adjusted to position the CCD sensor correctly. The camera is difficult to dismantle because several wires are soldered.
Care must be taken to discharge the capacitor of the flash, this may cause an electric shock and burn the camera board.
Those who want to try the repair, follow the link to the service manual.
http://elektrotanya.com/fujifilm_finepix_hs10_hs11_sm.pdf/download.html
Milton Maenishi

Fuji FinePix... | Answered on Jan 05, 2019


Panasonic help and support if available

Panasonic Lumix... | Answered on Jan 05, 2019


Hola Terry desconozco los set up de esa c?mara Has probado reproducir lo grabado en una pantalla diferente a la de la c?mara
Si la imagen sigue en TONOS DE GRISES ,tendrias que dudar de alg?n set up o la c?mara esta en la funci?n visi?n nocturna o nightshot ese control deberias encontrarlo cercano al lente de la c?mara suerte saludos desde Chile

Sony Cameras | Answered on Jan 05, 2019


it could be the age of the device or if you purchased it second hand from someone else its possible it cud have gotten wet at some time and caused it to malfunction,,you can find the same model or purchase a newer model here, be sure to shop in comfort and were you can get the best in products and services>>>www.discountbargainprices.com also you can follow my twitter wich you can find links were you can shop online at walmart or best buy>>>@discounts_ebay

Samsung Cameras | Answered on Jan 04, 2019

Not finding what you are looking for?
Cameras Logo

202,165 questions posted

Ask a Question

Usually answered in minutes!

Top Cameras Experts

Damen Wong
Damen Wong

Level 3 Expert

1950 Answers

Marvin
Marvin

Level 3 Expert

83850 Answers

Brad Brown

Level 3 Expert

17826 Answers

Are you a Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...