Hand Tools - Recent Questions, Troubleshooting & Support


They have an online form... but I have had no luck getting mine replaced. I have broke 2 so far.

Hand Tools | Answered on Oct 02, 2019


You will get all the information on Toolbox from here https://toolboxwidget.com. Download your PDF copy today or email us to toolboxwidget@gmail.com for ordering book.

Hand Tools | Answered on Sep 20, 2019


Hi! I'm sure there are a few more reasons why manhole covers are round, but here are some that I can think of: The round shape means that they can't fall into the manhole (like a square could). A round shape also means that it has a smaller surface area, so less material is needed to make them, making them cheaper to produce. Round manhole covers are also easier to move since they can be rolled on the ground.

Hand Tools | Answered on Sep 13, 2019


How do I dismantle the spiral from the outer casing of a yankee screwdriver

Stanley Hand... | Answered on Sep 04, 2019


check whether the wifi function of printer is on or not, there is utility of brother which searches the printer on pc after installation of the software , check it

Brother Usb... | Answered on Jul 30, 2019


Maybe your battery is died, you can replace it on

http://www.drillbattery.com.au/buybattery.php/makita_1220_power+tool+battery.html

603e8067-0762-423a-993c-d0ccf11a4787.jpg

Hand Tools | Answered on Mar 19, 2019


how hard can it be really???

Menards Hand... | Answered on Feb 09, 2019


it is a type of screwdriver bit

Hand Tools | Answered on Jan 03, 2019


they are typically made out of cast iron, often with little bits of concrete infused in them

Hand Tools | Answered on Oct 27, 2018


The pitch of the roof is described as the vertical rise of the roof divided by the horizontal span of the roof. The pitch of the roof is known as slope, and this happens to be a tangent function. When pitches are kept below 3.5, they are considered as low pitch, and when the pitch is kept from 3.5 to 7.5, it is considered as medium pitch anything above than 7.5 is considered to be a steep pitch. Depending on your requirement and style of construction you can decide the pitch of your roof. Click on Gotcha Covered Contracting to know more about roofing.

Hand Tools | Answered on Oct 07, 2018


It sounds like the ground has settled around the area where the leak is, hence the traveling water. The right way to fix the problem would be to remove the porch, dig up around the basement wall, apply a sealant to the outside of the wall, install weeping tile and re-grade the soil to drain away from the house. Your best bet to begin with may be to try to re-grade the soil so it is sloping away from the house, however this is only a temporary patch, if temperatures get below freezing there is a possibility that moisture in any crack in the wall could cause further cracking and leaks.

Hand Tools | Answered on Sep 19, 2018


I have a box of 5000 8mm 960/101 Vanguard Primo Staples - offer me something to cover the postage!

Hand Tools | Answered on Aug 29, 2018


Dimple the spot with a hammer and punch.

ASG Jergens... | Answered on Jun 13, 2018


When you are working with brick or concrete, you should check out the Black & Decker DR670 Hammer Drill. It is specifically made to tackle this purpose.

Hand Tools | Answered on Jun 07, 2018


This is just generic instructions just to give you an idea of placement and mounting. I am not sure if your vise turns or not and that would be a big factor also. It depends on where you want it, if anything is close that will interfere with the vise or whatever you have in the vise. Depends how thick the spot is where you want to mount it. If the place is not very thick, use bolt and heavy washer on top of the vise and a heavy washer, a lock washer and nut on bottom. In place of the lock washer and nut, you could use locknut. If the bench where you want to mount is too thick for bolts, use at least 2" lag bolts with heavy washers with the lag bolts as big as the vise holes will accept. You will need the vise as close to the edge without it hanging over the edge of the bench. This is so you will be able to open and close the vise without obstruction. If placement of the vise isn't a big deal, the center edge of the bench would be great although I always mount mine on one end of the bench because of better movement of the part in the vise. Goodluck.

Hand Tools | Answered on Jun 03, 2018


Unfortunately you need an expensive scan tool that can read all the other individual modules of a car. The Mercedes Benz cars have many of these and without information, it is very hard to work on.
It sounds like a body module is acting up.

Hand Tools | Answered on Apr 22, 2018


This torque wrench requires 2 LR44 button batteries (1.5V ea). Here's an Amazon page for this type:
Strip of 10 Energizer A76 LR44 1 5v Alkaline Batteries



Home Depot provides the manual PDF for download on their website:

https://www.homedepot.com/catalog/pdfimages/5f/5f26d0d8-9508-4807-80aa-3654f94e6609.pdf

Hand Tools | Answered on Apr 02, 2018

Not finding what you are looking for?
Hand Tools Logo

536 questions posted

Ask a Question

Usually answered in minutes!

Top Hand Tools Experts

Don Numinen
Don Numinen

Level 2 Expert

69 Answers

Dan Apthorp

Level 3 Expert

2824 Answers

Bill Boyd

Level 3 Expert

53746 Answers

Are you a Hand Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...