Music - Recent Questions, Troubleshooting & Support


What kind of casters are you installing? There are two types, ones that have a shaft sticking up from the base and ones that only have the flat base with four screw holes - I recommend using the flat base ones. There is no real easy way to open up the bottom of the cabinet as it is glued and then covered with the tolex or similar material. If you have the ones with a shaft I recommend getting the other type. The shaft has a socket you have to install in the bottom which makes them removable. There is no reason to remove the casters so get the ones that are screw mounted.

Peavey Music | Answered 17 hours ago


You could buy a Lehle switch, or simply use one on each separately. If you are using a multieffect unit you could make a Y cable to take the output to both amps but that will not allow you to select the drive channel - you still need the Fender footswitch for that, one for each amp. Lehle is a German company and they make a lot of different footswitch combinations but you will pay for the convenience.


I recommend the Fender single button footswitch for this use - Type: Footswitch
  • Number of Footswitch Buttons: 1
  • Manufacturer Part Number: 0994052000
  • It's about $35.00 each, compared to the Lehle which starts at $200. Just put the two side by side and make a metal bar to attach to the two switches - then you have a single bar to activate both drive channels at the same time. I recommend using aluminum bar stock with holes drilled into it for the switches, or find a C channel aluminum bar that will put the footswitch buttons in the channel. You can also make it one inch overhang past both switch bodies and then use bolts to keep the bar in place. If I was doing this I would mount the footswitches on a board and secure the bar to be on top of the footswitches, using coil springs to maintain the bar's alignment vertically at the end bolts.
  • Fender Music | Answered 17 hours ago


    I've also been looking HD500 schematic, but never got it.
    You can use X3L schematic as a reference and compared.
    Some sections of the X3L diagram, similar to the HD500.
    By the way, what is the problem with your HD500? Maybe I can help or share.
    HD500
    25897258-xykdzr1cdriwl1tmr4ngy0qt-1-0.jpg X3L
    25897258-xykdzr1cdriwl1tmr4ngy0qt-1-1.jpg

    Line 6 POD HD500... | Answered 22 hours ago


    https://www.manualslib.com/manual/99237/Marshall-Amplification-Mg15msii.html

    Marshall... | Answered Yesterday


    Look at this:-
    https://en.wikipedia.org/wiki/Line_level

    The Music | Answered Yesterday


    Yes..these amps due have fuses.
    Check to make sure the fuse is good, it should be close to the power cord in the back under a small, black, screw on type knob.
    capture1-0ghfle5x44c02sj0jxmykf2w-1-0.png You should also check the power on/of switch and power cord for issues.

    Peavey Music | Answered Yesterday


    Possible IC chip shorted or failure on the fader board.

    Roland Music | Answered 2 days ago


    press knob 1 and 2 and rec at the same time , then power on , then knob bank D , power off and on ,,,,, ready
    Greetings Gerrie ( Holland )

    Korg Kaossilator... | Answered 3 days ago


    Casio CDP has Auto Power Off: 30 minutes after last key operation, Auto Power Off can be disabled.
    Please read the manual.

    If it turns itself off while playing, I would try to buy a new AC Adapter to test. DC cable of AC adapters are often broken internally after much "bending".

    Casio Music | Answered 3 days ago

    Not finding what you are looking for?
    Music Logo

    22,740 questions posted

    Ask a Question

    Usually answered in minutes!

    Top Music Experts

    The Knight
    The Knight

    Level 3 Expert

    76016 Answers

    Marvin
    Marvin

    Level 3 Expert

    83850 Answers

    Brad Brown

    Level 3 Expert

    17805 Answers

    Are you a Music Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...