Washing Machines - Page 9 - Recent Questions, Troubleshooting & Support


Unplug washer for 30 minutes. Plug back in se if opens. If not take off top panel off washer. There is a latch to release door.

Whirlpool... | Answered on Oct 03, 2019


your hot water goes through the water heater so contaminates settle in the heater. the cold does not, there is a screen inside the fill valve where the hose hooks to the valve on the machine. if this in not plugged then the fill valve will have to be replaced. because of the build up of contaminates..

Kenmore Washing... | Answered on Oct 03, 2019


Sounds like either a wire has come loose from the switch or the motor that spins the the ( may be integral part of switch ) has gone bad.

Kenmore Washing... | Answered on Oct 03, 2019


Because quilts, towels, etc. hold a lot of water, they will only release that water during the spin cycle. If the spin rate is too high, the machine will sling water over the top of the tub thence down and onto the floor. To prevent this, reduce the spin rate from high to low. If you find they are still too wet, run a second spin, only, cycle on a higher setting.

Kenmore Washing... | Answered on Oct 02, 2019


Tray to drill another holes below the originals and cut ribs of old ones to put springs on. If not take 8 awg copper wire, band like hook, and glue down on casing with a two-component epoxy.

Electrolux... | Answered on Oct 02, 2019


Turn off the deep clean and extra rinse cycle options.

Maytag Washing... | Answered on Oct 02, 2019


My book says for the Axxis WFL 2050/WFL 2060 : from the left while looking at it from the front: detergent for wash, stain remover, middle: fabric softener, fabric conditioner, right one: detergent for soaking agent. (Do not use chlorice bleach in this wasking machine).

Bosch Axxis WFL... | Answered on Oct 01, 2019


My machine is showing E1

Hisense... | Answered on Oct 01, 2019


It sounds like there is most likely an Earth/Ground fault with the machine? There are several reasons for this, but without more precise details it is difficult diagnose.

Washing Machines | Answered on Oct 01, 2019


Have you checked the continuity in the mains power cable, there could be a break somewhere in the cable itself.
Another place that has been known to cause a problem is the connecting block inside the machine, where the mains cable connects to the machine. If there has been a bad connection at this point, the cable, or connectors can overheat and burn causing a bad / broken connection, and failure of the machine.
I hope this helps??

Washing Machines | Answered on Oct 01, 2019


Check that the load is within the 6kg limit and not entangled into a ball, which will unbalance the drum. Separate the items and try again. I believe Bosch has a telephone help line.

Bosch Washing... | Answered on Oct 01, 2019


Original advice in 2014 from Kenjo, on another website:
f21 is worn brushes in the motor replace them and to reset the f21 code.... close the door, turn timer dial to position 8 going clockwise, hold in the spin speed button whilst turning dial to position 9 let go of spin speed button and return dial to off position.

Bosch Washing... | Answered on Oct 01, 2019


Check your user instructions, if you have them. If not, download a copy from the maker's website.
Have you checked that the drain filter is clean?
If it's clean, take the washing out of the drum (use a big bucket), and try to resume the cycle with the drum empty. The E4 code may indicate an unbalanced load.

Washing Machines | Answered on Oct 01, 2019

Not finding what you are looking for?
Washing Machines Logo

258,185 questions posted

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

Brad Brown

Level 3 Expert

18108 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...