LG WM - Recent Questions, Troubleshooting & Support


water will not drain says oe

LG WM2487H Front... | Answered on Feb 12, 2019


You can turn the power on, and hit the spin speed button, and then start it. It should drain out.

If your still getting an LE error, and already have replaced the Hall sensor, it's most likely the Stator. If you know your date of purchase, this is most likely still under the 7 or 10 year warranty. Meaning LG pays for the part (over $100.00+),

LG WM-0532HW... | Answered on Feb 08, 2019


This dE error or fault code to indicate that the door is not latching properly. Check the lid or door operation to be sure it's not binding and that the door alignment is correct. Also, check the door/lid hinges to be sure they're not binding. Finally, make sure the door catch is in place and not broken. You may need to replace the door hook/catch or the door lock assembly.

LG WM Washing... | Answered on Oct 29, 2018


LG Tromm Washing machine te error. The manual says to call for service. Not much help there. The reason for the error is the thermistor circuit (resistive element that becomes less resistive as it increases in temperature). The thermistor acts as a heat sensor. In many cases, the error occurs because the wireing harness is too tight at the bottom of the drum and one of the wires in this circuit becomes disconnected with all of the movement of the drum (unbalanced load, normal cylcing etc).

1. Unplug the washing machine from the wall. The thermistor circuit is at line voltage (110 in the U.S.) and it will bite! So do this first before proceeding.

2. Move the washer out so you can get access to the back of it.

3. Remove the stainless panel (the one that is not painted, it is large (aprox. 16x18 inches). It is held in place by 4 phillips screws.

4. Locate the thermistor connection block near the bottom of the machine, at the center of the wash drum. It is the small white connector that has two wires running to it. One wire is dark blue, the other is light blue. Insure that neither wire has pulled out of the connector. If either of them have, repair the connector and provide enough extra wire ( aprox. 2") to provide cable relief.

5. If the cable connector and wires are ok, there are other solutions here that recommend either cleaning or replacing the thermistor.

Good luck to you.

LG WM2688HWM... | Answered on Oct 15, 2018


Unfortunately you won't find one.

LG only supply their servicing manuals to their repair centres and strictly enforce their copyright, so the manuals are not available to the public and when they do occasionally appear the material has been stolen.

Usually I'd recommend a generic repair manual such as the one by Haynes, but LG's direct drive system and a number of other unique technical features mean that the Haynes book isn't as useful as it could be. The WM3431HW is a large capacity and technically advanced washer dryer so it's certainly not as straightforward to service as a traditional front loading washer or dryer. Many LG spare parts can also be difficult to source outside of their own approved servicing organisation.

I respectfully suggest that you either get LG to fix your machine or post a question on this site describing the problem to see if we can assist you.

LG WM3431 Front... | Answered on Sep 26, 2018


see the diagram:
7_3_2012_12_37_48_pm.gif7_3_2012_12_38_03_pm.gif7_3_2012_12_43_24_pm.jpg

LG WM3431 Front... | Answered on Sep 26, 2018


Basically, we have excellent washing machine service center in Hyderabad very tough to objects are the guideline segments of choosing the washing machines. LG corporation presenting various models of Washing machines in the market and the association have a quality LG washing machine service center in Hyderabad and they deliver the benefit for satisfactory services in the time over the Hyderabad region. http://aktechnoservice.com/lg-washing-machine-service-center-in-hyderabad

lg washing machine service center...-cni0rihjrfc0cavwhfrsnoma-5-0.jpg

LG WM2688HWM... | Answered on Sep 05, 2018


AK Techno Service is one of the best http://aktechnoservice.com/lg-washing-machine-service-center-in-hyderabad/ . Front load top load semi-automatic drum failure, PCB repair service etc.
Here,you can find any type of solutions for your LG Washing Machine.

b72bed06-5439-421e-8bf7-379e0ff4e9a1.jpg

LG WM2688H Front... | Answered on Sep 03, 2018


did you unplug it,leave it unplugged for 5 minutes and plug it back in,if it's to hard to get to plug flip the breaker and leave the power off for 5 minutes or longer when you power it up again the door should unlock.here's a link to check hope it helps
https://www.google.com/search?q=lg+front+load+washer+how+to+manually+open+a+locked+door&oq=lg+front+load+washer+how+to+manually+open+a+locked+door&aqs=chrome..69i57.21935j0j8&sourceid=chrome&ie=UTF-8#kpvalbx=1

LG WM3431 Front... | Answered on Sep 03, 2018


You have a fault microprocessor, or the "Brain" is sporadically faulting... You need to get this looked at... it isn't a minor thing unfortunately... look get a firm "Quote" from a reliable service center man

LG WM2455 Front... | Answered on Aug 19, 2018


A DE Error Code is indicative of a “Door Error”. This indicates that the washing machine door is not shutting, locking or opening. This means that there is something faulty with the door switch and locking mechanism . You should get this replaced or you may have water where you do not want it. biigg53566

LG WM-2277HW... | Answered on Aug 13, 2018


the best way to drain the machane is to lean the machine back prop something under it and then using a bucket take the drain hose out an bring it as low as you can to the floor. This will make it easer for you to open the front at the bottom an clean the drain trap ,it is possible that there will be a little water left in there good luck

LG WM2487H Front... | Answered on Jul 15, 2018


if the bearings are rusted or seized u need to change main seal near bearings. was it noisy b4 you looked at bearings?could be broken spider that holds bowl.please reply if u need more help

LG WM1814CW... | Answered on Jun 29, 2018


After searching for the answer as to why my LG WM2455H wouldn't start unless I unplugged it and then plugged it again, and trying many "solutions", such as holding the power and start buttons for x amount of seconds, I finally found one that worked. Just before ordering a new control panel, I decided to search one more time for an answer, and found a young man claim that his uncle told him the answer to solving the problem. It's a little weird, and I was very skeptical, as you will be, but it DID WORK to let my washer power on after running cycles of wash. Here it is: Within 12 seconds, push in the POWER button and let go, then open and close the washer door, repeat by pushing in power button again, and let it go, then immediately open and close the washer door again. Do this six times within a 12 second time span. According to the young man on youtube, this procedure RESETS the controls. I would still be a little skeptical, except my machine behaves like it's suppose to now. PLUS, I did nothing that might be attributed to the solution (except think about how I was going to move the heavy washer away from the wall to replace the Control Panel I planned to buy). So, I hope this works for you. It certainly saved me a lot of time and money.

LG WM2455 Front... | Answered on May 16, 2018


The *dreaded* "LE" error is overwhelmingly caused or triggered by incorrect type detergent **OR** too much *HE* detergent (a special low sudsing detergent).
In all LG washers-when too much detergent has been used-this will cause the "LE" error to be displayed & the wash cycle will be interrupted. Unplugging the washer for more than one minute will cause the MAIN BOARD (computer) to power down and re-boot when the washer has been plugged back in.
On LG washers built *before* 2008-after several "LE" error events-the error *cannot* be reset by unplugging the washer. This indicates that the HALL EFFECT SENSOR has failed and will need to be replaced.
On all LG washers built during and after 2008-a more robust resistor was used in the HALL EFFECT SENSORS-which eliminated damage caused by higher electrical loads placed upon the sensors due to oversudsing. HALL EFFECT SENSORS virtually never fail in 2008 and newer LG washers but the "LE" error will still occur if too much or the wrong type of detergent is used. This will be "resettable" by unplugging/replugging the washer.
The CORRECT amount of HE (High Efficiency) detergent to be used is as follows:
HE : (2) Tablespoons Per Wash Load
HE 2X : (1) Tablespoon
HE 3X : (1) Teaspoon
USE THESE AMOUNTS RELIGIOUSLY-NO EXCEPTIONS-IN ALL FRONT LOAD WASHERS WITH 3.0 cu ft DRUMS AND LARGER

Read more: The Dreaded LE Error Code in LG Washing Machines: Diagnosis / Troubleshooting, Root Causes, and Repair ' Washer Repair ' Fixitnow.com Samurai Appliance Repair Man http://fixitnow.com/wp/2010/08/03/the-dreaded-le-error-code-in-lg-washing-machines-diagnosis-troubleshooting-root-causes-and-repair/#ixzz2nlabX1Gv
Follow us: fixitnowsamurai on Facebook

LG WM2233H Front... | Answered on Apr 07, 2018

Not finding what you are looking for?

-2,388 questions posted

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Marvin
Marvin

Level 3 Expert

84027 Answers

jimorris77

Level 3 Expert

411 Answers

Paul

Level 2 Expert

381 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

LG Washing Machines

  • Forum

View Most Popular

  • LG Washing Machines
Loading...