Pioneer Audio Players & Recorders - Recent Questions, Troubleshooting & Support


Press TUNE+ & AUTO SURR/DIRECT keys continuously for 2 sec. and it will tell you the fault it encountered if the receiver is in otherwise working condition.

Pioneer... | Answered Yesterday


Only way to fix this is to replace the digital board.

Pioneer Audio... | Answered on Sep 12, 2019


How do you get it out of protect mode?

Pioneer... | Answered on Aug 31, 2019


Hello,
Unfortunatelly your receiver has failed. The front panel is telling you one of the power modules is probably bad. Not an DIY type of repair. These parts are near $40.00, plus cost of replacing.
Look at options to replace your trusted receiver with a new one.
Good luck

Pioneer VSX-D411... | Answered on Aug 19, 2019


Hi Ramon, as you say, the protection circuit is working, you would have a problem in the power supply or in the audio outputs of speakers
I suggest you disconnect, all the speakers and test if the fault continues, if it does not continue, connect the speakers one by one and test until the possible fault is detected
If you disconnect and stay the same, I suggest you look for a specialized technical service
If you have knowledge and technical expertise, I give you the link to download the service manual of your Pioneer
I hope you can solve the problem
Regards Franco Dosil

Hola Ram?n, por lo que comentas, esta trabajando el circuito de protecci?n, tendr?as un problema en la fuente de alimentaci?n o en las salidas de audio de parlantes
Te sugiero desconectar, todos los parlantes y probar si continua la falla, si no sigue, conecta de a uno los parlantes y prueba hasta detectar la posible falla
Si desconectas y sigue igual, te sugiero busque un servicio t?cnico especializado
Si tienes conocimientos y pericia t?cnica, te paso el link para que descargues el manual de servicio de tu Pioneer
Espero puedas resolver el problema
Saludos Franco Dosil
https://www.manualslib.com/manual/1259236/Pioneer-Vsx-523-K.html
https://elektrotanya.com/pioneer_vsx-523-k_vsx-533_rrv4418_sm.pdf/download.html

Pioneer Audio... | Answered on Aug 13, 2019


Hi Joshyinoman, your subwoofer, is active, that is, it has its own amplifier, just take the bass audio signal from your Pioneer
Check if it is properly plugged into the power outlet, if the signal cable is properly and correctly connected to the Subwoofer Out of the Pioneer
If all this is well, then you have a problem with the internal amplifier, if so, look for a specialized technical service
I hope you can solve the problem
Regards Franco Dosil

Hola Joshyinoman, tu subwoofer, es activo, es decir tiene amplificador propio, solo toma la se?al de audio de graves de tu Pioneer
Controla si esta bien enchufado al toma corriente, si el cable de se?al, esta bien y correctamente conectado en la salida Subwoofer Out, del Pioneer
si todo esto esta bien, entonces tienes un problema con el amplificador interno, si es asi, busca un servicio tecnico especializado
Espero puedas resolver el problema
Saludos Franco Dosil
https://www.pioneerelectronics.com/ephox/StaticFiles/PUSA/Files/VSX-818V-K.pdf

http://www.pioneer-latin.com/downloads/vsx-918-k%20-%20spanish.pdf

Pioneer Audio... | Answered on Aug 13, 2019


Hello Anonymous, you can have dirty heads and guides, also the internal key Rec-Play could be wrong
You should do a full maintenance of the cassette system
Consult a specialized technical service
Greetings Franco Dosil

Hola Anonymous, puedes tener sucios los cabezales y las gu?as, tambi?n podr?a estar mal la llave interna Rec-Play
Deber?as hacerle un mantenimiento completo al sistema de cassette
Consulta un servicio t?cnico especializado
Saludos Franco Dosil

Pioneer Audio... | Answered on Jul 21, 2019


Hi, Try pushing the "Advanced Surround" and "Enter" buttons together for about 3 seconds.

Pioneer VSX-D712... | Answered on Jul 18, 2019


Could be a component failure other than fuses in the transformer circuit. Maybe a defective transformer

Pioneer Audio... | Answered on Jul 14, 2019


I sounds like you may have a problem in either one of the Regulator circuits, or, one of the Power Amplifier outputs. If the protect circuit detects DC or Low Impedance on one or more of the speaker lines, it will not fire up the high power section of the power supply. Further troubleshooting will require some working knowledge of power amp and power supply circuits. I've got a .pdf copy of the Service Manual if that will help you.
Please let me know what your level of troubleshooting ability is, and whether the manual will help you.
-Petra

Pioneer Audio... | Answered on Jul 14, 2019


In the manual Error 23 states the USB stick is not formatted with the FAT16 or FAT32 filesystem, which is the only supported filesystems supported on the unit.

Pioneer... | Answered on Jul 10, 2019

Not finding what you are looking for?
Pioneer Logo

6,186 questions posted

Ask a Question

Usually answered in minutes!

Top Pioneer Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5686 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1176 Answers

Ben Armstrong

Level 2 Expert

360 Answers

Are you a Pioneer Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...