Sony BRAVIA - Answered Questions & Fixed Issues


hello Dear
this is panel problem please replace panel
Thanks
M Nasir

Sony BRAVIA... | Answered on Apr 14, 2019 | 66 views


Aron,

To perform a reset you will need to disconnect the TV completely from power for at least 30 seconds, if this doesn't resolve your problem then you may have hardware that has expired in your device. Without physically looking at your device I can't say with certainty what your problem is, it could be your PCB. There are video's online you can visit on how to test a PCB for faults.
If you are not comfortable troubleshooting your device I would suggest contacting a local electronic repair shop near you, however I will link you to a generic instructional video showing you how to perform basic troubleshooting of your device.

Hope this helps,
Best regards


https://www.youtube.com/watch?v=qxG3hmmvkJs Testing LCD TV Power Supply BoardsSTEP BY STEP
fixya-aioep5zungdwqwtpjd23ghga-3-0_0.png

Sony BRAVIA... | Answered on Mar 08, 2019 | 45 views


Use code search on your URC to find something that works. If a search through all codes stored in the URC fails, try a different one.

Sony Bravia... | Answered on Mar 01, 2019 | 46 views


Although I am just guessing, most Sony equipment uses metric screws. Go to a Home Depot or similar store and take the piece that you have that contains the threaded fittings and they will help you find the screws you need. https://www.manualslib.com/manual/793567/Sony-Kdl-32xbr6.html?page=7#manual This page of the manual gives some info about the screws such as not longer than 1/2" (or 12mm) to prevent damage to the set. Sony customer service may be able to supply replacement screws too.

Sony BRAVIA... | Answered on Feb 18, 2019 | 39 views


Go to the initial set up procedure and disable it.

Sony BRAVIA... | Answered on Feb 14, 2019 | 152 views


Replaced circuit board under warranty.

Sony BRAVIA... | Answered on Feb 09, 2019 | 1,488 views


Open internal fuse or power supply failure

Sony BRAVIA... | Answered on Jan 23, 2019 | 47 views


Unplug from wall for 60 secounds then plug back in. See if that works.

Sony BRAVIA... | Answered on Jan 19, 2019 | 49 views


Press the HOME button on the remote control.
Select Settings.
Select System Settings.
Select Customer Support.
Select Factory Settings.
Select OK.

Sony BRAVIA... | Answered on Jan 18, 2019 | 88 views


THe antenna came of. Did you use it and is it giving troubles now? If not, then don't mind and leave it.

Sony BRAVIA... | Answered on Jan 17, 2019 | 64 views


here's blink codes for sony bravia


1 blink abnormal AU Power Voltage
2 blink abnormal d5v/a9v power voltage
3 blink Abnormal panel voltage
4 blink backlight failure
5 blink abnormal main power voltage
6 blink abnormal speaker voltage
7 blink internal temp. rise
8 times ic5000

that helps?..

Sony BRAVIA ... | Answered on Aug 30, 2018 | 14,715 views


Yes ,you should replace the main board ,because you can'nt repair HDMI interface.
Abctay.com Wholesale tv parts,include TV power supply board, logic board, TV LED screen

Sony BRAVIA ... | Answered on Aug 02, 2018 | 167 views


If the line is present in all inputs and modes, there is a problem with the LCD Panel. The only way to fix it is to replace the whole LCD Panel which is very expensive (usually around $1000+ for 40" Sony). Unless the TV in under warranty, it is usually around the same price for a new TV.

Sony BRAVIA... | Answered on Jul 15, 2018 | 1,832 views


07107.

Sony BRAVIA... | Answered on Apr 21, 2018 | 173 views


You may get an answer if you asked for a specific code.

Sony BRAVIA ... | Answered on Apr 14, 2018 | 335 views


Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts.
https://electronicshelponline.blogspot.com/
In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.

Sony BRAVIA... | Answered on Mar 03, 2018 | 182 views


If you wish to get some details; visit the site linked here. Pull up older posts.
https://electronicshelponline.blogspot.com/
Line faults & possible causes to LCD & Plasma screen are given with illustrations. You can get an idea about the fault to an extent. Faults to all LCD & Plasma screen are similar, irrespective of its brand and screen size.
Search the site by type in the "BRAND NAME" of your device; (Exclude the model number), in the "Search box at the top right of the display window of the Homepage" to get gathered related posts

Sony Bravia... | Answered on Mar 03, 2018 | 35 views


for Bravia's.. To turn off the demo mode, press and hold the MENU button on the TV for more than 10 seconds. The message Demo mode: Off will appear on the screen.
Let me know if this helps.

Sony Bravia... | Answered on Feb 21, 2018 | 117 views

Not finding what you are looking for?

-2,826 questions posted

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76060 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1691 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...