Whirlpool Washing Machines - Recent Questions, Troubleshooting & Support


Water Temperature Sensor Error - Check the Water Temperature Sensor,Heating Element and Element Relay.
If during the water heating step in wash cycle,the water temperature sensor(NTC) value is out of range,or the heating element circuit has failed,the F05 error code will be displayed - Check connections to
the Sensor,Heating Element and Relay.

Whirlpool Duet... | Answered Yesterday


Hi i am a technician.This is sensor problem near motor. If problem is not solved by replacing it then call me or whatsapp on +917802911328. I have 100% solution

Whirlpool... | Answered 2 days ago


The F24 error indicates the water temperature sensor is not reading the expected temperature. This could be caused by a problem with the water temperature sensor, the heating element, the wiring or the control board. First unplug the washer and check that all of the wires are correctly connected. Next check the resistance across the temperature sensor; it should be 9.7K Ohms at room temperature. If this reading is not close to 10K Ohms, replace the sensor.

Next check the heating element and that the wiring has continuity between the sensor and the control board. (You're checking for breaks in the wires.) Replace any damaged parts. If these parts are okay, then the control board has to be replaced.

Please add a comment with the model of the Spors Duet washer if you'd like me to try to find a parts diagram or price list for the unit.
I hope this helps.

Cindy Wells

Whirlpool... | Answered on Mar 21, 2019


Either coupler was installed incorrectly or transmission is bad.

Whirlpool... | Answered on Mar 21, 2019


Depending on the age of the machine there could be a number of factors going on here. There are shock absorbers in the machine that maintain balance of the drum while it is spinning. Sitting on top of the drum there is usually a large concrete block and some springs attached that limit the machines away from side to side and backwards and forwards. All of these parts work in conjunction with one another to stop or limit excessive vibration of the drum during a spin cycle. If these are worn or are degraded excessively then this could account for the extra vibration. It could also be that the machine is being overloaded which would cause this vibration too. As for the plastic that is tough to pin down. Ideally we could do with images of the plastic to advise you further.

Whirlpool... | Answered on Mar 19, 2019


Check that the door seal is on properly. There is a spring that goes around the seal to hold it on

Whirlpool... | Answered on Mar 18, 2019


Perhaps the main circuit board or motherboard? It wouldn't hurt to check it out and look closely at all of the little "pathways" between the various components, it's highly probable that the intense vibration and movement caused a solder joint to come loose or a component may not be connected as it should be. Break out your voltmeter and use the continuity tester to your advantage to verify circuits are completed as they should be. I'd imagine you'll find an issue, if not my apologies but that's been the case in my experience more than once. Best of Luck Friend!
d9cba470-6b1f-4bc2-b6ca-e7dc0c317a2f-nuhf2ssaswwsu1mfl2kxuue2-4-54.jpeg

Whirlpool... | Answered on Mar 17, 2019


Maybe its because youre timer
Problem or timer contact or fuse blowing coz of heavy load ,unload and check the power supply

Whirlpool... | Answered on Mar 15, 2019


Disconnect it from the mains supply for 5 minutes. Then restart the cycle. It should pump out. Then you can power off and restart from scratch.

Whirlpool... | Answered on Mar 11, 2019


For heavy machinery cars etc. luckily there are many websites
that can help you repair
for eg site like reliable-store is ver y active in this.. instant help, emails and all that's fantastic

Whirlpool... | Answered on Mar 11, 2019


Open the door, put your hand in and onto the top of the inner drum. Push upwards, if it moves upwards for more than a few millimeters it is probably the bearings worn.

Whirlpool... | Answered on Mar 11, 2019


The dispenser is flushed with water to prevent clogging with softener residue.

Whirlpool... | Answered on Mar 07, 2019

Not finding what you are looking for?
Whirlpool Logo

Family Lines

33,171 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Sal De

Level 3 Expert

2699 Answers

Marvin
Marvin

Level 3 Expert

84027 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...