Polaris ATV - Answered Questions & Fixed issues


Will the crank shaft turn I would take the plug out and use a 1/4 in exstion and put it in the sparkplug hole needs to be about 10in to were it dont fall down in there and push to make sure the motor is not locked up

Polaris ATV | Answered on Nov 21, 2019 | 194 views


Your engine codes should only be in two digit numbers and you should not have codes that end with any zeros.check engine light should flash like count the flashes three flashes pause then 6 flashes would be code 36 then longer pause between codes then you have more than one code after a long pause it may flash 4 times then short pause then two flashes would be code 42 witch is engine coolent temperature high voltage a code 56 is fuel pump open load/short to battery or short to ground should start with one flash short pause then two flash meaning 12 then codes will repeat ,to start flash engine codes turn key off and on three times in less then 5 sec then leave on

Polaris ATV | Answered on Nov 13, 2019 | 71 views


Need to test to see if power is being sent from the key switch to the ignition I would think bad fuse or bad ignition switch

Polaris ATV | Answered on Nov 13, 2019 | 128 views


You have lost power to your ignition when it is in the on position check fuses or look for broken wires leading from ignition switch it could very well be in the switch it self

Polaris ATV | Answered on Nov 13, 2019 | 67 views


Ok the 6 amp fuse is for the ecm the 15 amp fuse is for the cluster one of the 20 amp is main power the outher 20 amp should be for the starter and charging circuit .your over heating problem could be in the fan temp sensor you will find it on the left side of the machine on top of the thermostat housing , take and disconnect the plug on it and jumper the two wires togather with key on fan should come on if it does replace fan temp sensor .if not visibly pull each fuse out and look to see if is burnt odds of the fan being bad is very uncommon. This will be all good if is an EFI 800 hope that is helpfull

Polaris ATV | Answered on Oct 26, 2019 | 66 views


define "stopping". If it involved using the new ignition switch, then I think a return to the dealer is necessary. You know it takes 3 times for them to get it right?

Polaris ATV | Answered on Oct 16, 2019 | 52 views


Odds are your carb needs to be taken apart, cleaned, reassembled and adjusted if needed.

Polaris ATV | Answered on Sep 27, 2019 | 88 views


You can improve the performance of your ATV with some extra parts and accessories. Here are a few performance enhancement tips that can be attained through such ATV accessories- Innovative Ideas to Improve Performance of an ATV with Accessories...

Polaris ATV | Answered on Aug 30, 2019 | 524 views


T map sensor voltage to high or t map sensor voltage to low

Polaris ATV | Answered on Jul 13, 2019 | 192 views


Should be petcock to pump, pump to carb, carb to engine.. and you have a vacuum line that makes the pump work ..usually from carb/intake to pump.

Polaris ATV | Answered on Jun 11, 2019 | 121 views


Have you check the injectors ? If anything is coming out.

Polaris ATV | Answered on May 26, 2019 | 75 views


Your problem is not clear. So you may do some more research and then take a decision.
I found this video from youtube. I hope this can be helpful. video link: https://www.youtube.com/watch?v=01Rc80ykfVs

Polaris ATV | Answered on Apr 29, 2019 | 266 views


Hello there,

I found this video for you. I hope this could help you!
video from youtube: Polaris sportsman 570 code problem fix https://www.youtube.com/watch?v=YR8DN5oWazc

Polaris ATV | Answered on Apr 25, 2019 | 182 views


I am guessing you mean the float is sticking and leaking gas? If so, remove the carb and have it sonic cleaned. The jet that the float opens and closes and should be inspected for wear. In some instances, the float should be weighed for fuel saturation. That may prevent proper floatation in order to fully close the fuel flow once the bowl is full allowing the fuel to continue flowing.

Polaris ATV | Answered on Apr 25, 2019 | 84 views


Test the compression using a compression tester.
My guess a valve is stuck closed.
A compression test will show this.

Polaris ATV | Answered on Mar 31, 2019 | 133 views


check wiring under vehicle going to diff for breaks

Polaris ATV | Answered on Mar 22, 2019 | 134 views


Spray some starter fluid into the throttle body. If it starts then it is a fuel problem. Check the fuses for injection operations.

Here is a video that might help. https://www.youtube.com/watch?v=3rhe2BzIOLA

Polaris ATV | Answered on Mar 19, 2019 | 75 views

Not finding what you are looking for?
Polaris ATV Logo

4,072 questions posted

Ask a Question

Usually answered in minutes!

Top Polaris ATVs Experts

unhappyed

Level 2 Expert

106 Answers

john h

Level 3 Expert

22486 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you a Polaris ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...