20 Most Recent
kawasaki 2010 Prairie 360 4x4 Questions & Answers
How many turn it take on the air mixture screw to get my 2010 Kawasaki 360 4x4 to start?
For the initial settings - 03-12
- lightly seat the pilot all the way to the back - lightly, too much torque and you'll ruin the o-ring in there - then back out the pilot screw 1 & 1/2 turns. From there - you let it run for 10 minutes or so and then adjust the idle to 1,300 +/- 50 rpm - turn your handlebars left and right after adjustment of the throttle lever to make sure it's okay and not binding up - and do your adjustment from the throttle stop screw. According to the specs, once you set that pilot at 1,300 +/- the rest of the adjustment is done with the throttle stop screw. If you do all that and it's still not picking up fuel - definitely give the intake/carb boot a good look over for any cracks or anywhere vacuum could escape - and if it still doesn't pick up the fuel - give the throttle set screw a turn or two. Had a 2000 Yamaha XT225 carb I rebuilt a few weeks ago - adjusted everything as instructed - but it wasn't picking up the fuel. I gave the throttle set screw about a 1/3 turn in to put a little nudge on the throttle and it fired right up. All The Best and Good Luck - Justin Lee, 17 South Industries, LLC
Oil pump problems
pump is suffering excessive oil pressure
you are very short on the details of the failure --broken shaft , gears , chain housing etc but I would be checking oil passage blockages, faulty pump pressure regulator spun bearing that the pump feeds into the oil galleys
Bypassing immobilizer
all of the auto start kits use the immobilizer bypass. look into one of those and see what they use to bypass it.
Assembly diagram for a recoil on a 1999 Polaris 400 xplorer
Assembling a recoil system on a Polaris 400 Xplorer involves several steps. While I can't provide an actual diagram here, I can outline the general steps involved in assembling a recoil system:
- Preparation: Ensure you have all the necessary parts for the recoil assembly including the recoil starter, recoil housing, recoil spring, and any other associated parts.
- Mounting the Recoil Housing: Begin by mounting the recoil housing onto the engine. It typically bolts onto the engine casing.
- Inserting the Recoil Starter: Place the recoil starter mechanism into the recoil housing. It usually fits into grooves or mounts within the housing.
- Attaching the Recoil Spring: Connect one end of the recoil spring to the recoil starter mechanism and the other end to a fixed point within the recoil housing. This provides the tension necessary for the recoil starter to function properly.
- Installing the Pull Cord: Thread the pull cord through the hole in the recoil starter mechanism and tie a knot at the end to secure it. Wind the pull cord around the recoil starter as per the manufacturer's instructions.
- Testing: Before completely sealing the recoil housing, give the recoil starter a few pulls to ensure it functions smoothly and retracts properly.
- Final Assembly: Once you're satisfied with the recoil assembly, bolt down any remaining covers or components to secure the recoil system in place.
Always consult the specific service manual for your Polaris 400 Xplorer for detailed instructions and diagrams tailored to your exact model. Additionally, if you're unsure about any step, it's best to seek assistance from a professional mechanic or someone experienced with small engine repair.
4/20/2024 12:13:30 PM •
ATVs
•
Answered
3 days ago
Can't find how to trouble shot the horn on my 2015 Kawasaki mule
take off the horn unit power it direct if it works its ok, if not replace, next step wire a small bulb into the horn wires and press the button if it lights the switch is ok, if you have a circuit tester put one end on the battery ground and check for power in the horn wires if their is power there put the lead on battery positive and press the horn button if there is no power their the switch or wiring is faulty
4/16/2024 10:19:40 PM •
ATVs
•
Answered
on Apr 16, 2024
Not finding what you are looking for?