Question about Polaris ATV

Open Question

I Got a 2011 Polaris Ranger 500, need to know the cylinder and head bolt torque specs

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
emissionwiz

Marvin

  • 85216 Answers

SOURCE: 2005 Tucson

camshaft sprocket bolt 58-72 ft. lbs. crankshaft pulley bolts 108-132 ft. lbs. crankshaft pulley center bolt 80-94 ft. lbs. cylinder head bolts cold engine 65-72 ft. lbs. warm engine 73-80 ft. lbs. cylinder head rear cover bolts 69-86 in. lbs. flywheel/Driveplate bolts 94-101 ft. lbs. intake/Exhaust manifold nuts/Bolts 11-14 ft. lbs. jet valves 13-16 ft. lbs. main bearing cap bolts 36-39 ft. lbs. oil pan bolts 51-69 in. lbs. oil pan nuts 43-60 in. lbs. oil pan drain plug 33 ft. lbs. oil pump cover bolts 72-84 in. lbs. oil pump relief valve plug 29-36 ft. lbs. oil pump sprocket nut 25-28 ft. lbs. Rear oil seal retainer bolts 84-108 in. lbs. rocker arm shaft bolts 14-15 ft. lbs. rod bearing cap nuts 23-25 ft. lbs. silent shaft sprocket nut 22-28 ft. lbs. spark plugs 15-21 ft. lbs. thermostat housing-to-Engine bolts 86-114 in. lbs. timing belt tensioner bolt 32-40 ft. lbs. valve cover bolts 43-61 in. lbs. water pump-to-Engine bolts alternator brace bolt 14-20 ft. lbs. all others 9-11 ft. lbs. water pump pulley bolts 72-84 in. lbs.

Posted on Sep 08, 2008

Ad
chuck943

Chuck Martin

  • 783 Answers

SOURCE: Head bolt torque specs needed for 96 tbird 3.8

Head bolts are torque to yeild so you MUST use new bolts.
Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:

  1. 20 Nm (15 lb-ft).
  1. 40 Nm (30 lb-ft).
  1. 50 Nm (37 lb-ft)
Loosen retaining bolts one at a time two to three revolutions and retighten as follows:

Long bolts:
  • Tighten to 40-50 Nm (30-37 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Short Bolts:
  • Tighten to 20-30 Nm (15-22 lb-ft).
  • Rotate an additional 175-185 degrees.
  • Go to next bolt in sequence.
Here is a pic of the sequence
http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif

Posted on Mar 19, 2009

inspectmycar

Chris Biddle

  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

Anonymous

  • 122 Answers

SOURCE: need cylinder head gasket torque specs.

looks like there is special sequence to reassemble and tightening, a quick note replace any bolts that have two punch marks.tighten as follows: x x x x x 10 4 2 6 8 x x x x x 7 5 1 3 9 torque all down to 15 ft lbs torque to 30 ft lbs plus 90 degrees. Good luck!

Posted on Sep 18, 2009

Anonymous

  • 74 Answers

SOURCE: Need Cylinder head bolt torque specs and sequence

  1. Install the cylinder head gasket. Ensure the arrows point towards the front of the engine. The left cylinder head gasket has the letter L stamped next to the arrow.
  2. Notice
  3. This bolt is designed to permanently stretch when tightened. The correct part number fastener must be used to replace this type of fastener. Do not use a bolt that is stronger in this application. If the correct bolt is not used, the parts will not be tightened correctly. The system or the components may be damaged.

  4. Install the cylinder head.
  5. Install new cylinder head bolts. Tighten
    Tighten the cylinder head bolts to 50 N·m (37 lb ft) in sequence.
  6. Use the J 36660-A to rotate each cylinder head bolt 120 degrees in sequence. Use the J 36660-A to rotate the four center cylinder head bolts an additional 30 degrees in sequence. Refer to Notice Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

d429947.gif

Posted on Mar 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Votage at front diff 2011 polaris ranger 500 will not go in 4x4 but has 14 volt all the time how does it switch with voltage all the time


first thing, find out why you have 14 volts going to it. trace the wires back. test it at the switch. there shouldn't be 14 volts going any where. test other things to see what you got let me know

Apr 06, 2017 | ATVs

1 Answer

How do you replace a front ball joint on a 2011 polaris ranger 500


like doing an auto --jack up vehicle remove wheel rotor and brakes to access the ball joint --they are pressed in --remove lock bolt separate from spindle remove locking c- clip and either buy borrow or rent a ball joint press and remove ball joint replace is in reverse

Sep 13, 2016 | Polaris 2011 Ranger 500 EFI

1 Answer

What would cause my 2011 polaris ranger 500 to cut off on gas


Same answer have the computer control scanned for fault codes.

Sep 13, 2016 | Polaris 2011 Ranger 500 EFI

1 Answer

What are the torque specs for the head


Jac, you can google search your year make and model cylinder head bolt torque.
Check the attached links,Manuals and guides, Good luck with your Bike
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

Service Manuals for Download in PDF
ATV Service and Repair Manuals
ATV TROUBLESHOOTING AND MAINTENANCE

Mar 04, 2016 | ATVs

1 Answer

Need torque specs. head bolts , cylinder bolts , valve clearance


Hi ! for an informantion, please visit the website below. If you need more information about a specific electrical issue you can reach me at motor@motorpartstore.com.

Feb 04, 2016 | ATVs

1 Answer

Hard to shift out of 1st gear


hard to shift gears - Polaris ATV Forum

www.polarisatvforums.com > ... > Polaris Sportsman
Jun 28, 2010 - my 06 500 efi creeps and sometime is a little hard to shift. the dealer told me ... inline. if its off a little when you are stopped and trying to shift the tranny has... 2013 RZR XP 900 .... shop, for first service and to put in a new belt, blew up the firstone already. ... what makes a polaris crew hard to change gears.

Won't shift with motor running. Need help please - Polaris RZR ...

www.rzrforums.net > ... > General RZR > RZR-S Specific Discussion
Mar 6, 2012 - It will not shift in any gear with the motor running, but if I turn it off I can.... First Name: Jeanie ... 2013 Grizzly ... LE - Muzzy, UMP, Donaldson, TS Seats, FixMyToys parts.. and a lot of hard work .... 2005 polaris sportsman 500 shifter problems stuck in reverse ... polaris ranger 700 crew wont shift when running. How to adjust shifter
Nov 27, 2013
Issue: In gear, but will not drive
Oct 22, 2012
Gear Grinding
Oct 7, 2012
HELP trans is hard to shift
Jan 26, 2011
More results from www.rzrforums.net

Ranger Problems & Solutions [Archive] - PRC Polaris


Dec 30, 2015 | Polaris 2013 Ranger Crew 500

2 Answers

Just bought this bike had no manuals with it I need to know about checking and changing oil


PDF]Sportsman 400 H.O. Sportsman 500 H.O. - Polaris

cdn.polarisindustries.com/polaris/.../parts-manuals/9923420r01_lo_res.p...
... parts and acces- sories, available through our online store at www.purepolaris.com. Have ... 2012 SPORTSMAN 400/500 HO Owner's Manual. P/N 9923420 ...

Polaris Sportsman 500 HO Owner's Manual - ManualsLib

www.manualslib.com > ... > Offroad Vehicle > Sportsman 500 H.O.
View and Download Polaris Sportsman 500 HO owner's manual online. PolarisIndustries All-Terrain Vehicles Owner's Manual. Sportsman 500 HO Offroad ...

2011 Sportsman 400/500 Service Manual - Polaris ATV Forum

www.polarisatvforums.com > ... > ATV Repair and Maintenance
Apr 11, 2011 - Indy Red 2011 Sportsman 500 H.O. -Polaris rear rack extender -Ricochet a-arm guards -Polaris fender bag -Koplin hand guards w/mirrors Owners, Service, and Parts Manuals
Sep 14, 2012
2005 Polaris 500 H.O. ATP service manual
Aug 12, 2011
Service manuals
Nov 29, 2010
Service Manual
Sep 23, 2010
More results from www.polarisatvforums.com

Dec 21, 2015 | Polaris 2011 Sportsman 500 H.O

1 Answer

Overheating and stalling


Search Results

    2011 XP 800 overheating - Polaris Ranger Club

    www.prcforum.com/.../26-ranger.../29358-2011-xp-800-overheating.ht...
    Sep 9, 2010 - 10 posts - ‎5 authors Member #: 12988; Join Date: Sep 2010; Location: Glasgow, Missouri; Posts: 11 ... He said it started "stalling" and running rough then he noticed the heat ... My week old 2011 Ranger 800 XP/LE doesn't run hot but the fan does ... Thread: 2011 ranger 800 xp **hot** **won't run
    10 posts
    Apr 4, 2012
    2011 800XP overheating and getting worse.
    10 posts
    Sep 20, 2011
    Thread: 2010 ranger 800 xp overheating
    10 posts
    Aug 21, 2011
    Thread: 2010 Ranger 800 stalling from low idle when ...
    8 posts
    Sep 1, 2010
    More results from www.prcforum.com

Nov 05, 2015 | Polaris 2010 Ranger 800 XP

1 Answer

I need to know how to time valve the pistons to the valve train, I need torque specs for the cylinder and head.


Down load the autozone app and it will have all the torque specs that you need for any car

Sep 24, 2013 | Polaris 2004 Sportsman 400

Not finding what you are looking for?
Polaris ATV Logo

Related Topics:

707 people viewed this question

Ask a Question

Usually answered in minutes!

Top Polaris ATVs Experts

unhappyed

Level 2 Expert

106 Answers

john h

Level 3 Expert

22486 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you a Polaris ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...