Question about Polaris ATV

Open Question

All wheel drive switch. When it is down it indicates 2 wheel drive on the dash, when it is in the middle it indicates 1 wheel drive. Is that correct for my 2018 Polaris Ranger 570 Full Size?

Posted by on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
perkins48

Thomas Perkins

  • 14809 Answers

SOURCE: What type of gas do I use in my Polaris Ranger 570

Minimum octane 87 R+M/2. Ethanol content 10% or less - per my 2015 manual.

Posted on Sep 29, 2016

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Won't start


Hey Craig,
An internal combustion engine needs three things to run if its assembled correctly:
1. A timed spark
2. Compression
3. Correct Air/Fuel ratio
Get yourself a manual, it will be invaluable,,
Auto Truck Repair Manuals by Chilton Haynes Clymer Factory

Jun 27, 2017 | ATVs

1 Answer

Lost power to dash lites and four wheel drive switch


Peter, probable blown fuse, check all fuses.
Check the attached links,Manuals and guides, Good luck with your Bike
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How to Diagnose Motorcycle Electrical Problems Dennis Kirk Inc
ATV Service and Repair Manuals
Service Manuals for Download in PDF

Mar 08, 2016 | ATVs

1 Answer

Wont go in 2 wheel drive but switch works light come on dash ?


2004 Sportsman 700 AWD not working..... - Polaris ATV Forum

www.polarisatvforums.com > ... > ATV Repair and Maintenance
Feb 18, 2013 - Go Back · Polaris ATV Forum > Polaris ATV Technical Discussions > ATV ... AWD wont engage. 2. The instrument / speedo works. 3. The AWD switch is ...Polaris ATV Junkie! .... four wheel drive not working polaris sportsman. Won't go into 4 wheel drive
Feb 1, 2013
4 wheel drive not working
Nov 13, 2011
2004 700, 4WD engages by itself
Oct 28, 2011
4wd is stuck on
Dec 3, 2009
More results from www.polarisatvforums.c

Nov 29, 2015 | Polaris 2004 Sportsman 700 Twin

1 Answer

Kawasaki forum, I have a 2002 kawasaki prairie 650 4x4 that will not switch into 4 wheel drive. It stays in 2 wheel only. Help please


Honda FourTrax & Kawasaki Prairie 650 ' Outdoor Life

www.outdoorlife.com/articles/gear/.../honda-fourtrax-kawasaki-prairie-6...
Honda decided not only to get into the 500cc-class automatic 4x4 camp, but to do ...by three electronic shifting programs: one for high-speed driving on easy trails; ... this innovation: Kawasaki made the Prairie 650 capable of starting in gear.

Sep 12, 2015 | ATVs

2 Answers

How do I fix my front wheel drive system on my 2004 ATV 400 Sportsman Late model? After extensive work and parts replacement my all wheel drive is not working.


Just a suggestion but you should consider soldering all your electrical connections to insure they are weather and vibration proof. Additionally, I added a small 3 amp circuit breaker, but a 1.5 to 2 Amp automotive fuse and fuse holder will do nicely.

Process:

1- Disassemble the 'Instrument/Light' cluster cover.

2- Remove the 'Radiator access' panel.

>>>Perform This Test BEFORE Proceeding and make SURE all power is OFF!<<<

3-On the drivers LEFT side of the radiator access area, locate two (2) connectors, each with SOLID GREY wires and BROWN wires with a WHITE Stripe on top and smaller diameter Solid Grey and Brown wires with a White stripe leading down.
--a) Disconnect both connectors by pulling the top and bottom sections away from each other. (DO NOT pull the WIRES, use the connector body to pull).
--b) Test EACH of the two (2) connectors with the SMALL DIAMETER wires leading down. (see Hub Coil Connectors pix)
--c) Using an OHM meter, measure the resistance across the two pins (one connector at a time) for each connector. Depending on the accuracy and sensitivity of the meter, each connector should read between 25 and 28 OHMS. NOTE: If EITHER of the two (2) Hub Coils reads ZERO (0) or less than 25 or Greater than 28 OHMS STOP!!! The Hub Coil itself OR the wires OR the connectors may be defective or in need of repair!
--d) Using an OHM meter, on EACH of the two connectors, measure the resistance between one pin of each connector and GROUND (any bare metal point on the ATV frame). NOTE: If EITHER of the two (2) connectors resistance to GROUND reads anything GREATER/ABOVE than ZERO ( 0 ) OHMS STOP!!! The Hub Coil itself OR the wires OR the connectors may be defective or in need of repair!

>>>If the test in 'c)' or 'd)' FAIL STOP, DO NOT proceed!! The Hub Coil itself OR the wires OR the connectors may be defective and MUST be repaired before ANYTHING else is done!<<<

4-(For my model) On the right handlebar, check the lamp in the AWD switch to make sure it is not burned out or missing. Replace lamp if necessary. (Not essential to the AWD operation, just nice to have to confirm voltage is being applied to the front wheel Hub Coils)

5-In the 'Radiator Access' area, locate the Red/White stripe wires providing (switched) full time + (battery plus) voltage (accessory power) via a ¼" female connector. "Accessory Leads" - in the wiring diagram.

6-Using a volt meter (or continuity light), CONFIRM that the terminal is OFF (NO voltage) when the ignition switch and the 'Engine STOP/START switch (on the left handlebar) are both OFF, and has + (positive) battery voltage, when the ignition switch and 'Engine STOP/START switch are both ON, with the engine NOT running.

Jan 15, 2015 | Polaris 2004 Sportsman 400

1 Answer

06 polaris 700 my 4wheel drive will not ingage. I have a brand new front diff on it.


The front end works off 12volts.If you have moisture in your dash your dash may not let your 4 wheel drive work and it could also not let your atv start if it doesn;t every start unplug your dash but your dash has to work to have 4 wheel drive.

Oct 28, 2014 | Polaris ATV

1 Answer

Turf mode not working


turf mode is where only one wheel is powering the sportsman.
sounds like the left wheel is the one that would drive it.
i can not figure out if it is the rear left wheel but it may be. i would see if there is a problem with that.

Apr 04, 2014 | Polaris 2013 Sportsman X2 550

2 Answers

Why doesn't my 4 wheel drive work


it could be, polaris uses an electronically controlled lock in hub. broken wires or bad switch also.

Apr 06, 2013 | Polaris 2004 Scrambler 500

Not finding what you are looking for?
Polaris ATV Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Polaris ATVs Experts

unhappyed

Level 2 Expert

106 Answers

john h

Level 3 Expert

22486 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you a Polaris ATV Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...