Holden Cars & Trucks - Page 9 - Recent Questions, Troubleshooting & Support

This might sound an obvious answer but have you tried twisting the controls on the centre console? There will be a set of large twist knobs on the lower half of the centre console. One will be marked with numbers, one will be marked as a red/blue bar and the other will be marked with little arrows. Twist the numbers to 0 and twist the colour bar to blue. The numbers are the fan speed and the colours are the temperature, (Red is hot and Blue is cold).

Does the fuse control the relay for the glow plugs because I would think a 15a fuse would be too small for the glow plug circuit itself...

Possibly the starter motor, could be the battery feed to the motor on the large terminal, could be an engine ground issue as well.

There are a lot of issues that this could be caused by and it could be as simple as holding the button down on the ESP switch for 5 seconds or it could be a wheel alignment issue. If the unit was driven on a slippery surface and it came on, you have to go through at least 3 driving cycles for it to reset.

My ex-wife makes $250 /hour on the laptop.She has been fired for seven months but last month her pay check was $17147 just working on the laptop for a few hours. Read more here>>>HERE www.Pays99.cOm

this is not an uncommon problem. you will need to go to your local holden dealer and purchase a new gear shift button. To fit the new gear shift button you will need to remove the centre console insert and the screw that holds the t-bar trim in position..

Behind the front right headlight you will find an inline black plug/socket pair that have been connected together. One is the connection to the RH fog light connection, the other is the aircon compressor clutch connection. This plug/socket pair are physically compatible but they will create an electrical short circuit and blow the 20amp ignition fuse if they are connected together. Disconnect them and your short circuit will be resolved.

Yes because it you tamper with it may void warranty if any

check with your local mechanic sounds like you did it wrong

Since been no problem probably faulty sender or sensor but would Need to have scanned for trouble code of what is causing light ---and problems that would set off can be multi such as low fluid.. Overheating ...low pressure ..high pressure ..gear sensor these are some of reasons it would flash

Possible transmission fault or just damaged wiring to the transmission control unit.

Bad fuel pump or ignition issues. Coil or cables hav worn connection. But first put key in on off position threetimes..on four try startn. If it fires then the residual fuel supply is not workn and ull need anew checkvalve to repair

Dealer visit to re-programme it.

Only one on the left tailight.

try wiggling the steering wheel and gently turn key at same time to unlock steering lock

Videos, but basically, you just undo the bolts in the seat frame and any electrics. https://www.google.com/search?q=remove+the+front+seats+from+a+1996+holden+sb+barina ..

find and buy a service manual. youll be glad you did

Holden Fault Codes - Delco - AFI Australia - Fuel Injection ...

afiaustralia.com.au > tech-tips > 91-fault-codes > 313-h...

Holden Fault Codes - Delco. Diagnostic Fault Code List for Delco System Camira, Commodore VN-VP 12 No spark pulses at CPU or else good system, ...

fault codes barina Questions & Answers (with Pictures) - Fixya

www.fixya.com > tags > fault_codes_barina

Holden barina tk 2007 engine won't start. ? run the fault codes check that the cam shaft is turning ( broken timing belt) check immobiliser for correct operation ...

Holden Barina P1700 Engine Trouble Code

p1700.enginetroublecode.com > holden-barina

Holden Barina P1700 OBD-II Diagnostic Powertrain (P) Trouble Code Information Page. Reason for Holden Barina P1700 and find the solution for the code ...

P1100 Holden Barina DTC Code ' EngineDTC.com

enginedtc.com > p1100-holden-barina Your Holden Barina engine control system detects a problem, the computer stores the diagnostic trouble code P1100 in its memory. To figure out what is wrong ...

Solution On the lower-right corner of the dashboard, you'll find the rotary switch that controls the headlights. On the same switch panel (just to the left of the main headlight switch) are a pair of sliding controls that control the headlight aiming (the right-hand slide) and the dashboard-light brightness (just to its left). When the car's headlights are turned on, the dashboard lights are automatically dimmed, and sometimes this provides insufficient light to see the gauges clearly in bright daylight. But by holding the adjustment slide in the up position, you can turn the dashboard lights to their brightest level of illumination.