Hyundai Cars & Trucks - Page 5 - Recent Questions, Troubleshooting & Support

Question edited for clarity and add maker. Question moved to model category.

Shift Cable Repair procedures - Automatic Transaxle Control ...

helantraad.com https://www.helantraad.com > shift_cable_repair_proc... 1. Air cleaner assembly and air duct. · 2. Battery and battery tray. · 3. Remove the nut (A) from the manual control lever. · 4. Remove the shift cable (B) from ...

2008 Hyundai Elantra Automatic Transmission Shifter Cable

Hyundai Parts Pro https://www.hyundaipartspro.com > Automatic-Trans... Automatic Transmission Shifter Cable. 2008 Hyundai Elantra. Genuine Hyundai Part - 467902H100 (46790-2H100). Ships from Hyundai Parts Pro. Rating: 4.8 · ‎361 reviews · ‎$105.19 ..

The firing order is 1, 2, 3, 4, 5, 6. Stand with the engine's belts and pulleys nearest to you and the transmission furthest away. The Left side of the V is the odd numbers. Number 1 nearest to you, number 3 in the middle and number 5 furthest away from you. The Right side of the V is the even numbers. Number 2 nearest to you, number 4 in the middle and number 6 furthest away from you. If yours has the single coil block for all six spark plugs the three plugin points run as pairs. They are cylinders 1 then 4, 2 then 5 and 3 then 6. Commonly working left to right with the plug in ports pointing upwards.

You may need to replace the power lock actuator motors inside the door . Alternatively, you can try disassembling the paneling on the left side under the steering wheel and removing two black relays on the side closest to the steering wheel. Then remove the relay covers and clean the contacts with a 1/8 fine strip of 600 wet/dry sandpaper. SOLVED: 2010 Hyundai Santa Fe 3.5l. Why the key remote - Fixya 2010 Hyundai Santa Fe: driver's door lock locks only - Fixya

vThe best solution you'll get from books at www.reliable-store.com These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

There are only 3 ways to get the Unlock code. I turned it into a Tip because I typed it so many times. https://www.fixya.com/support/r29874205-need_vehicle_radio_code ..

Inertia switches are only a feature on Ford vehicles. There is always confusion on the names of items related to fuel supply. look at this answer regarding the Santa Fe, relay and fuse.

Where my inertia switch on my 07 Hyundai santa fe, Yeah, by

JustAnswer https://www.justanswer.com > Hyundai Questions Jul 29, 2017 - Your vehicle does not have an inertia switch. The system only has a relay and fuse in the engine compartment fuse box. 1 answer · Top answer: Hi, My name is Jay Your vehicle does not have an inertia switch. The syst https://www.google.com/search?q=2010+hyundai+veracruz+inertia+switch+location ..

You put the first number in with number one key, the second number with key number two and so on till the four numbers are entered ther press key five .

The fuel cutoff switch is located on the drivers side strut tower next to the brake master cylinder. press down on the top rubber part and you should hear a click.

This could be caused by the deterioration of this small flexible coupler located in the steering column. The good news is you don't need to have the entire steering column or intermediate shaft replaced as most people think. This tiny, $2.00 flexible coupler and two hours of labor could be the answer to your problem. Nov 25, 2015

Hyundai / Kia clicking noise in steering column

..

2017 Elantra steering "clicking" sound when turning the ...

Reddit https://www.reddit.com > Hyundai > comments > 201... Dec 27, 2018 - It's the rubber coupler in the steering column. It's not really dangerous or hazardous as the steering still works fine, it's just annoying. 2010 Hyundai Elantra making clicking noise when turning the ... Jan 7, 2022 2010 Hyundai Elantra - Popping sound in steering wheel ... Feb 7, 2016 2011 Hyundai Elantra, steering wheel makes weird rattling ... Sep 8, 2022 HELP needed - 2018 Hyundai Elantra Steering Noise - Reddit Nov 7, 2021 More results from www.reddit.com

Hi Joe It is sort of a guess, but your headlights are powered from the battery and cause a drain when on, so the regulator provides extra volts to compensate the battery charge being depleted. Except your question heading says 'not to charge'. The question body says 'why the alternator is charging when I turn the headlights on'? Should that be 'why the alternator is NOT charging when I turn the headlights on? If that is the case, you need an auto electrician.

is battery in good condition. It sounds like you have a bad battery. https://www.wheelsjoint.com/hyundai-sonata-dashboard-lights-flicker-and-wont-start/

Here is the fuse box diagram, but the Elantra appears to have a rather funky battery fuse! Most vehicles have a main battery fuse but it is on the battery connector wire. If you put in a new ECM, was it programmed to the vehicle? https://www.autozone.com/batteries-starting-and-charging/battery-fuse/hyundai/elantra-gt

Hyundai Elantra (XD; 2000-2006) fuses and relays

Fuse Box Diagrams https://fuse-box.info > hyundai > hyundai-elantra-xd-... The fuse box is located on the driver's side of the instrument panel behind the cover. The location of the fuses in the passenger compartment: Hyundai Elantra ( ...

Nope. The knock sensor detects knocks in the engine and retards detonation in the timing.

Car not shifting would be bad vacuum operated actuator on outside of tranny or bad syncros or other internal transmission parts

Sounds like you have air in the cooling system.

press and hold eject....is there a cd in it?

Unless you ran out of fuel, this is the only way, an auto electrician with a pro grade scan tool computer. Diagnose in 20 minutes. https://www.google.com/search?q=mobile+auto+electrician+near+me ..

I opened the hood and unplugged the sensor by the water jug for the windshield washer. Probably could add a little drop of RTV and let it dry so that it would push harder on that switch but then I would have to leave the hood open for several hours to let that glue dry. 3 days no problems

Pull stereo forward and get the last 4 numbers of serial number off the top of the unit. (It’s quiet easy)Add that number to 1212 and that number is the code. So if the last 4 numbers is 1234 +1234 the code is 2468. Push 1 till you get 2, 2 till you get 4 and so on. 5 is the enter button.
The small sticker is the serial number.